Pumps and Related Parts

The Waterway center discharge wet end has been discontinued and replaced with the E-Series Center Discharge wet end by the manufacturer. Please be sure which wet end you have as the parts are not interchangeable. The easiest way to identify which wet end...

This is a XP2e 1.5HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor would be about 9.0 Amps on high speed at 230V or 14.0 Amps on High at 115V. See the links below for seals, bearing and other parts...

This Wet End is a 2" x 2" 2.0HP 48 or 56 frame Ultimax Vico® that would normally be found an a 230V pump with 10.0 Amps High speed or 16.0 Amps at 115v..  This side discharge, 2" x 2" mbt which would measure about 3" edge to edge on the threads,...

This part is a Pump Union, 2" Female Buttress Thread x 1-1/2" Slip..    Half Union Fitting Complete Complete Pump Union Union Fitting Application Pump First Plumbing Connection Size 1-1/2", 2" First Plumbing Connection Type Female...

This part is a Complete Verticle Mount Style FMVP 1.0HP Aqua-Flo 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Adjustable Suction Side discharge 48 frame wet end for FMVP pumps only. This wet end is used with a 48 frame motor that...

You are buying a 3 HP 48 or 56 Frame Universal 2" X 2" Wet End / Pump complete with Barb, Silicon, Screws, Volute, Impeller, Seal, Face and the Wear Ring. This Wet End will work for a 2HP , 3HP or 4HP Motor To determine the HP refer to the chart below...

Vico/Balboa Ultima/Ultra Flo Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 3/4hp, it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 3/4hp (or greater) thru bolt...

This pump complete is not longer available but we have a solution.. If you need the motor click here and then click on the pump parts section.. Order the motor and then order the pump parts needed to complete the repair while reusing your pump housing....

This Pump is a 48Frame 115V 2 Speed with a 1.5-2.0 HP Wet End that features a 1 1/2" x 1 1/2" Center Discharge inlet and outlet Wet End that measures about 2 5/16" across the threads...  High speed Amperage is 13.3A and low speed is 4.1 Amps....

This part is a Complete Flo-Master FMCP 1HP Aqua-Flo 1-1/2" x 1-1/2" ( Which measures about 2 3/8" Across the Threads) Center discharge 48 frame wet end for 48FR pumps. This wet end is used with a 48 frame motor that would have about 8.0 Amps on High...

This Listing is for a (1) Speed Waterway Executive 56fr 230V 3 HP 2" X 2" Pump. Your sticker may say 4HP but based on the chart it is really a 3HP at 12 Amps. Measure the intake and pressure side threads and match them up before ordering.  This...

This part is no longer available you must buy a complete wet end to get this part. This part is a Faceplate found on FMHP and FMCP side discharge wet end faces.. Below will be links to the other related parts to this face: Shaft Seal Kit, PS-200, 5/8"...