Pump Wet Ends and Related Parts

This is a .75HP or 3/4HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End .75HP Motor that has about 7.0 Amps on High Speed at 230V and 7-8.0 Amps at 115V. This Impeller fits between the Face and the...

Vico, Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico. Rated at 3.0hp,which would be 8-10.0 Amps.. it is used in an Ultimax pump wet end, and must be installed on a 2.0hp (or greater) thru bolt motor.  Click here for...

This parts is an Executive 2 1/2" Mpt Threaded Face plate assembly (Which will measure about 3 11/16" Across the Threads) less the O-rings, Screws, Bleeder Plugs and other hardware needed to attach it to the volute..There is another version of the face...

This part is a Complete 1.5HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 48 frame wet end for XP2 pumps. This wet end is used with a 48 frame motor that would have about 9.0 Amps on High Speed on a 230V motor or 13.0...

This part is a 4 HP 56 Frame Waterway Executive 2 1/2" X 2" Wet End / Pump complete with Screws, Volute, Impeller, Seal, Face and the Wear Ring. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be...

Vico/Balboa Ultima/Ultra Flo Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 1.5hp,which is between 8 and 9 Amps.. it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 1...

No Longer Available.. Note: Due to a design change in the current XP2/XP2e pump wet ends, face plate or volute replacement is not suggested. Instead, replace the wet end to avoid issues with how it fits. Click for Complete Wet Ends Here.. This part is...

This is a XP2e 4.0HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V there are no 115V versions. See the links below for seals, bearing and other parts for...

  This is a 1HP Impeller with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.0HP Motor would be about 8.0 Amps on high speed at 230V or 12.0 Amps at 115V.   This Impeller fits between the Face and the...

This 2HP Impeller fits a Jacuzzi/Carvin Wet End only and would be found on a motor that is about 16.0 Amps on a 115V motor or 10.0 Amps on a 230V motor..... It can be found under the Name Thera-Max or Thera-Flo and is found on Jacuzzi Premium J Series...

This part is a Wear Ring for a Hi-Flo Impeller found in Waterway Hi-Flo pumps only.. The Inside Diameter of the wear ring is 1 13/16"...

This parts is an Executive 2" Threaded Face plate assembly (Which will measure about 3" Across the Threads) less the O-rings, Screws, Bleeder Plugs and other hardware needed to attach it to the volute..There is another version of the face with a 2 1/2"...