Pump Wet Ends and Related Parts

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 2.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 2.0hp (or greater) thru bolt motor. Shaft seal sold...

This part is a Complete XP2e 6.3” 4.0HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 14.0 Amps on High Speed on a...

This part is a Complete FMHP 2.0HP Aqua-Flo 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Side discharge 48 frame wet end for FMHP pumps. This wet end is used with a 48 frame motor that would have about 10.0 Amps on High Speed on a...

Jacuzzi J-Series Wet End Kit Bottom Suction, center discharge, 2"mjt, 48 frame wet end by Jacuzzi/Carvin. This wet end is used with a 1.0hp, 48 frame, thru-bolt style motor. The motor used may be either a single or dual speed. The complete wet end...

This part is no longer available you can only get this with a complete wet end.. This part is a Face Plate with Drain Plugs and Face O-Ring that fits Aqua-FLO XP2E wet ends only on the back of the face where the wear ring will touch will measure about...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 3.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 3.0hp (or greater) thru bolt motor. Shaft seal sold...

Vico/Balboa Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico/Balboa. Rated at 4.0hp, it is used in an Ultimax pump wet end, and must be installed on a 4.0hp (or greater) thru bolt motor. Click the below links for the...

You are buying a 3 HP 48 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Screws, Volute, Impeller, Seal, Face and the Wear Ring. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3...

This part is a Wear Ring that measures 2 5/8" inside Diameter and fits some Aqua-Flo XP2e and Xp3 Impellers except the 3.0HP Xp2e Impeller... That Impeller requires a different Wear Ring which measures 2 3/8" Inside Diameter.. Look at the chart in the...

This part is a Gasket for an AquaFlo A, Volute, 4-13/16"ID, 5-1/2"OD, Generic.. Part Type Gasket Inside Diameter 4-13/16"id Outside Diameter 5-1/2"od

You are buying a 5 HP 56 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Screws, Volute, Impeller, Seal, Face, Wear Ring, Bleeder Barb and Silicon.  The Bleeder Barb Replaces one of the plugs and is used to reconnect your previous...

This part is a Complete FMHP 1.5HP Aqua-Flo 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Side discharge 48 frame wet end for FMHP pumps. This wet end is used with a 48 frame motor that would have about 9.0 Amps on High Speed on a 230V...