Pump Wet Ends and Related Parts

The Waterway center discharge wet end has been discontinued and replaced with the E-Series Center Discharge wet end by the manufacturer. Please be sure which wet end you have as the parts are not interchangeable. The easiest way to identify which wet end...

This part is a 2HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0122 cast into the back and will measure about 3 3/4" wide with an eye width of 1 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This part is a Complete Flo-Master FMCP 1.5HP Aqua-Flo 1-1/2" x 1-1/2" ( Which measures about 2 3/8" Across the Threads) Center discharge 48 frame wet end for 48FR pumps. This wet end is used with a 48 frame motor that would have about 9.0 Amps on High...

You are buying a 3 HP 56 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Screws, Volute, Impeller, Seal, Face and the Wear Ring. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3...

This item is a 1/2" Air Bleeder Plug with Fine threads that can be found on the Newer style of a Sta-Rite Dura-Jet DJ Series Wet ends only.  If you need the O-ring for this plug only Click Here: Sta-Rite Pump, New Style Drain...

This part is a 3.0HP Power-Right Pump Impeller that would be found on a motor with about 12.0 Amps at 230V.. Closed face impeller made for the Power-Right 3.0ohp/6.0thp spa pump. Rated at 3.0hp, it is used in the Power-Right 9089X, 9094X, 9121X, PRC504...

This part is a Pump Face for a Vico Ultima Side Discharge wet end that is 2" which measures about 3" edge to edge across the threads.. The Seal Kits for this pump can be found here: Vico Seals 201 The other parts for this pump can be found here: Ultima...

This part is a Complete FMHP 1.0HP Aqua-Flo 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Side discharge 48 frame wet end for FMHP pumps. This wet end is used with a 48 frame motor that would have about 8.0 Amps on High Speed on a 230V...

This part is a 2.5HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0123 cast into the back and will measure about 3 3/4" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This part is a 2.0HP Sta-Rite Dura-Jet Complete 2" X 2" Wet End that fits both 48 or 56 frame motors and would fit a 230V Pump that is 10.0 Amps or a 115V pump that is 16.0 Amps.. The 2" fitting actually measures about 3" Edge to Edge across the threads...

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...