Pump Wet Ends and Related Parts

This is a 1/15th HP Impeller for an Aqua-Flo Circulation Pump 48 Frame Side or Center Discharge CMHP, CMCP and FMVP Series Wet End. This Impeller fits between the Face and the Volute of an Aqua-Flo CMHP, CMCP and FMVP Series Wet End. I would advise...

This part is an Aqua-Flo XP3 Pump 4.0HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4.0HP pump impeller to be on a 14 amp motor... Click here for the...

This part is an Aqua-Flo XP3 Pump 3.0HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 3.0HP pump impeller to be on a 12amp motor... Click here for the...

This part is an Aqua-Flo XP3 Pump 2.5HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 2.5HP pump impeller to be on a 10-12amp motor... Click here for...

Waterway Hi-Flo Wet EndSide discharge, 2"mbt suction/discharge, 48 frame wet end for the Waterway Hi-Flo pump. This wet end is used with a 12.0 Amp 3.0hp, 48 frame, thru-bolt style motor. The motor used may be either a single or dual speed. The wet end...

This part is a Wear Ring that only fits Guangdong LX or LP Impellers for a 48 or 56 Frame Pump Wet Ends and measures 3/4" thick from front to back... WUA Pumps.. Note: When Replacing some original LX Pump faces the wear ring was built into the face....

This O-Ring is a replacement for the Square Gasket that is found in the Sundance, Jacuzzi, Thera-Max, Thera-Flo, 2" Flat Style O-Ring..  Heater Union Part Type    O-RingPart Type    O-RingO Reference Number  ...

As of 11/2024 Aqua-flo has started to send this pump with a capacitor bump in an odd spot that may affect your installation. In light of that we are now sending this pump assembly out as a separate 10.5 Amp motor and a genuine 2.5 HP XP2 wetend. You...

You are buying an Air Bleeder Mountable Bleeder Fitting with a removable plug, a 1/4" Mpt X 3/8" Barb plug. This style set up is is usually found in Dimension One Hot Tubs in the Filter area and other brands as well.. Note; The plug is not sold...

This is a 4HP Seal, (2) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct Aqua-Flo...

This is a 4HP Seal, (1) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct Aqua-Flo...

You are buying a Kit that features (1) PS-200 Seal and (2) Bearings that fit most motors that are mated to Aqua-Flo Pump Wet Ends as well as Waterway " Viper" Wet Ends, The Professor silly Juice to seal the seal. This Seal is used in Most Aqua-Flo...