Pumps and Related Parts

This is a 1.5HP Impeller with a 2 1/8" Eye Width and a 5/16" Vane Width and 4" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor that has about 9.0 Amps at 230V. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2 Wet End...

This part is a 2 1/2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 2 1/2" Pump Union. The Pump Union Split Nut that measures about 3 3/4" on the outside and mounts to the existing Pump Union Body using 2...

This is a 1HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 1HP Motor that has about 8.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This is a 2HP Impeller with a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V. This Impeller fits between the Face and...

This Kit is an 3HP Impeller for an Executive 48 Frame Wet End up to 3HP Motor and a 56 Frame Wet End 3HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

This part is (1) 1/8" X 1/8" Barbed Coupler that fits 1/8" OD , 3/16" ID Clear Hose on each side. These are used for connecting Clear Hoses together in Hot Tubs or pools and commonly used in Air Button Switch systems.

This part is a Jacuzzi® J Pump Style Pump Union that can be used on 1 1/2" or 2" Plumbing systems. This union can receive a 1 1/2" plumbing part inside the back of the union or a 2" Plumbing part glued to the outside of the...

This part is a Run Capacitor that fits many 230V Pump Motors. When diagnosing pumps for a run capacitor concern you will find high amp draw, overheating, Noise and other concerns. This type of capacitor is really hard to dioagnose unless it is not...

This part is a Starter Capacitor that fits many 230V Pump Motors. When diagnosing pumps for a no start condition where it is powered up but just hums you can hand spin start the motor by taking a screw driver to the shaft in the back and spinning it or...

This item is a 1/4" Air Bleeder Plug with coarse threads that can be found on the old style of a StaRite Dura-Jet DJ Series Wetends only. The head of this plug will break off and leave the threads in the wet end face. You can take a flat screw driver and...

Grundfos Circulating Pump 230V with 1" Barbs... In my opinion this is a better pump than the Laing Brand... Spa Guy Note: If you are using this pump to convert from a Laing you will need this Conversion Kit If you want the same kit but need Glue Click...

This Listing is for a Waterway Executive 56fr 2 Speed 230V 3 HP 2" X 2" Pump. Your sticker may say 4HP but based on the chart it is really a 3HP at 12 Amps. This unit features a 2" X 2" Executive Wet End that can be moved from the 12 O'clock position to...