Pumps and Related Parts

Note: When you order this pump you will receive the newest version of the pump which is a baseless and you will receive the base as well.. This will be able to be installed in any position but you will have to install the base which may not line up...

This part is a 12" Piece of 1/2" Flex Pipe used with 1/2" Manifolds, Jet Bodies and other fittings......       740016011378,DW-17ST R , DW-17ST-ZD,89-555-1105,1.062",hose clamp,pipe,pipe clamp,clamp,roto,roto...

You are Purchasing a 6" Piece of 1/2" Flex Pipe used with 1/2" Manifolds, Jet Bodies and other fittings...... The list on this part is $12.99.   We have done a lot of extra work with videos and pictures to prevent you from choosing...

This part is a 12" Piece of 3/4" Flex Pipe used with 3/4" Manifolds, Jet Bodies and other fittings..       740016011378,DW-17ST R , DW-17ST-ZD,89-555-1105,1.062",hose clamp,pipe,pipe clamp,clamp,roto,roto...

You are Purchasing a 6" Piece of 3/4" Flex Pipe used with 3/4" Manifolds, Jet Bodies and other fittings...... The list on this part is $12.99.   We have done a lot of extra work with videos and pictures to prevent you from choosing...

This part is an Add On Air Bleeder kit featuring a Mountable Bleeder Fitting with a removable plug, a 1/4" Mpt X 3/8" Barb plug, (2) Clamps for each end of the tubing and 36" of Clear 3/8" ID and Silicon sealer..   This kit can be added if you...

This Part is (1) NON-Standard 2" Heater or Pump Union Gasket with a 2 5/8" Center to Center Lip. The gasket is 2 7/8" across on the outside the inside diameter is about 2" and the lip that fits into the union is 2 5/8"...

This is a 2.0HP Seal, (2) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 11.0 Amps on high speed at 230V or 16.0 Amps on High at 115V. Note: The three things you need to...

This is a 2.0HP Seal, (1) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 11.0 Amps on high speed at 230V or 16.0 Amps on High at 115V. Note: The three things you need to...

This is a Watkins Wavemaster 8000 or 8200 2.0HP Seal Kit & Impeller with a 2 1/8" Eye Width... This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081. Impeller...

This 1.5 Horse Power Impeller, (2) Bearings & Seal Kit fits a 48 Frame Pump Wet Ends manufactured by Guangdong LX Brand only. The pumps this Impeller, Bearing & Seal Kit fits usually have the part number WUA-150, WP-150 or LP-150 on the label...

This 1.5 Horse Power Impeller, (1) Bearing & Seal Kit fits a 48 Frame Pump Wet Ends manufactured by Guangdong LX Brand only. The pumps this Impeller, Bearing & Seal Kit fits usually have the part number WUA-150, WP-150 or LP-150 on the label...