Pump Impellers

Vico/Balboa Ultima/Ultra Flo Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 3/4hp, it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 3/4hp (or greater) thru bolt...

This part is an Impeller for a Sta-Rite DuraJet DJ Wet End that would be called 1.0hp-1.5HP, your motor should be 8.0-9.0Amp at 230V or 16.0 Amps at 115V.. The number on the back of the impeller will be 17400-0021 or 17400-0121 if you have a number on...

This impeller is no longer avaialve from the manufacturer but the one at this link wil work in its place: Impeller, Aqua-Flo, XP3, 4.0hp, For XP3 Pump 2 1/2" x 2 1/2" Wet End This part is a Waterway Viper Pump 4.0 Impeller exclusively for A Waterway...

This Impeller is obsolete but there is an Impeller that will work but there is only one choice and it will look different than your old impeller: Impeller, Vico Ultima Ultra Jet Flo,4...

Vico/Balboa Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico/Balboa. Rated at 2.0hp,which would be 8-10.0 Amps.. it is used in an Ultimax pump wet end, and must be installed on a 2.0hp (or greater) thru bolt motor...

Tnei part is no longer available you can only order the complete wet end found Here: Wet End, Waterway, Uni-Might, Iron-Might, 1.0HP, 1-1/2", 48 frame, 1.4A/115v Waterway Iron Might Circulation Pump Impeller for 1/8HP Pump Closed face impeller made...

This Kit is an 1HP Impeller for an Executive 48 Frame Wet End up to 1HP Motor and a 56 Frame Wet End 1HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

This part is a 2HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0122 cast into the back and will measure about 3 3/4" wide with an eye width of 1 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This part is a 3.0HP Power-Right Pump Impeller that would be found on a motor with about 12.0 Amps at 230V.. Closed face impeller made for the Power-Right 3.0ohp/6.0thp spa pump. Rated at 3.0hp, it is used in the Power-Right 9089X, 9094X, 9121X, PRC504...

This part is a 2.5HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0123 cast into the back and will measure about 3 3/4" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 2.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 2.0hp (or greater) thru bolt motor. Shaft seal sold...