Pump Impellers

Vico/Balboa Ultima/Ultra Flo Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 1.5hp,which is between 8 and 9 Amps.. it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 1...

This is a XP2e 4.0HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V there are no 115V versions. See the links below for seals, bearing and other parts for...

  This is a 1HP Impeller with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.0HP Motor would be about 8.0 Amps on high speed at 230V or 12.0 Amps at 115V.   This Impeller fits between the Face and the...

This 2HP Impeller fits a Jacuzzi/Carvin Wet End only and would be found on a motor that is about 16.0 Amps on a 115V motor or 10.0 Amps on a 230V motor..... It can be found under the Name Thera-Max or Thera-Flo and is found on Jacuzzi Premium J Series...

This part is a Impeller, Jacuzzi, J Pump, 1.0hp, 48FR, J Series, JCM Series, K Series, KM Series.. This is found on a Wet End that has a face like I show in the Photo Section only..  Impeller Type Closed Face Impeller Diameter...

Waterway Hi-Flo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 1.5hp, it is used in a Waterway Hi-Flo pump wet end, and must be installed on a 1.5hp (or greater) thru bolt motor. Shaft seal...

This impeller fits a Universal CMP Brand 3HP Wet End only and it requires a Special Seal that you will find a link to below.. This impeller may also have any of the following manufacturer part numbers stamped on the back: 27203-300-300, 27203-000-300,...

This is a XP2e 3.0HP Impeller.. The Impeller has a 2 3/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor would be about 12.0 Amps on high speed at 230V there are no 115V versions. Note: If your old impeller has a 2 3/8" Eye this is the...

This is a XP2e 2.5HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.5HP Motor would be about 11.0 Amps on high speed at 230V there are no 115V versions. See the links below for seals, bearing and other parts for...

This Kit is an 2HP Impeller for an Executive 48 Frame Wet End up to 2HP Motor and a 56 Frame Wet End 2 HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you...

This is a 2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 2HP Motor that has about 10.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This part is a face plate drain plug for Aqua-Flo pumps.. It does not come with an O-Ring you will find the link to that below.. Aqua-Flo Pump, Drain Plug, O-Ring Xp2, Xp2e, XP3, 7/16" ID, 3/32"