Pump Impellers

This Face Plate O-Ring Is 5 1/8" Inside Diameter and is 1/8" Thick. It is found on Aqua-Flo 1 1/2" x 1 1/2" (Which Measures 2 3/8" Outside of the threads on the Sunction and Pressure Side of the Wet End) These Wet Ends used the names Flo-Master,...

Drain Plug with O-Ring for Waterway Wet Ends Fits Executive, Viper, Hi- Flo, Iron Might, Spa Flo, Supreme, Mustang, Workman and More  We also offer the 3/8" Barb that replaces these plug in the case of using a Pump Bleeder System... This are found...

This Wear Ring only fits Waterway Executive 4 or 5HP Impellers for a 48 or 56 Frame Pump Wet Ends and measures 13/16" thick from front to back or some Intertek impellers... If you have a Waterway Executive 1,2 or 3 Horsepower Wet End it will require...

This is a .5HP or 1/2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End .5HP Motor that has about 6.0 Amps on High Speed at 230V and 6-7.0 Amps at 115V. This Impeller fits between the Face and the...

This kit is a Air Bleeder barbed plug and Silicon sealer usually used on a Aqua-Flo and CMP Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands of Hot Tubs just compare the pictures and...

Aqua-Flo Xp2 6.1" or 6.3"and XP2e Flo-Master Pump Face O-Ring fits around the Face of a Xp2 Pump Face exclusively for An Aqua-Flo Xp2 pump which has 2" inlet and outlet which measures about 3" across the threads... There are (2) Different versions of...

This wear ring measures 2 3/8" inside Diameter and fits only 3.0HP Aqua-Flo XP2e and Xp3 Impellers.. If you have 1.5, 2.0, 2.5 or 4.0HP they require a different Wear Ring which measures 2 5/8" Inside Diameter.. Look at the chart in the photo section...

This video is about a Jacuzzi J Pump Repair Kit How To Information...This type of pump can be found in many brands of hot tubs like, Jacuzzi, Jacuzzi Whirlpool,Blue Ridge, Gatsby, Whitewater, Echo, Hercules, Polynesian and many more... Wet End, Jacuzzi...

Waterway Viper Pump 5.0 Impeller exclusively for a Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a 14-16 amp motor...   Closed face impeller...

Waterway Viper Complete 5HP Wet End fits on a Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads... If you don't need a complete wet end a list of parts are below... Click Here for the Face...

Waterway Viper Complete 3HP Wet End fits on a Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads... NOTE: This wet end is now obsolete from Waterway but we offer an Aqua-Flo version that is identical in...

Waterway Viper Complete 4HP Wet End fits on a Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads... If you don't need a complete wet end a list of parts are below... Click Here for the Face...