Complete Wet Ends

This part is no longer available you must buy a complete wet end to get this part. This part is a Faceplate found on Wavemaster 3000 side discharge wet ends..   Drain Plug Location    6,8 o`clockSuction Connection (Physical...

This Wavemaster 5000 Face Plate O-Ring Is 5 1/8" Inside Diameter and is 1/8" Thick.   The below List is other parts related to this Part: Watkins, Wavemaster 5000, Vendor Code 4081, Shaft Seal Kit, Silicon & Tool Buna Watkins, Wavemaster...

This Wavemaster 3000 Face Plate O-Ring Is 5 1/8" Inside Diameter and is 1/8" Thick.   For other parts related to this part see the below links:

This part is a replacement wear ring for Wavemaster 5000 Pump Impellers with a 1 3/4" Eye.. The ring measures about 1 3/4" inside the wear ring and 2 3/16" at the widest part and about 3/4" tall..   The below List is other parts related to this...

This part is a replacement wear ring for Wavemaster 3000 Pump Impellers with a 1 3/4" Eye.. The ring measures about 1 3/4" inside the wear ring and 2 3/16" at the widest part and about 3/4" tall.. For Other related parts see the below...

This is a 1HP Impeller for a Wavemaster 3000 Code 04184 48 Frame Side Discharge pump. This Impeller fits between the Face and the Volute of a Wavemaster 3000 Series Wet End. I would advise replacing the Seal when you replace the Impeller. This Impeller...

Watkins Vendor Code 4081 Older Style Wavemaster, 4000, 6000, 7000, 8000, 8200, 9000, 9200... 48Frame Pump Face O-Ring Only fits around the Face of this Pump Face... There are (2) Different versions of the Face plate O-Ring on the Xp2 Wet Ends.. The...

This Part is a 2 1/8" wear ring that is used between the impeller and the wet end face on Watkins Vendor Code # 4081, Wavemaster, 4000, 6000, 7000, 8000, 8200, 9000, 9200.. This wear ring serves as a seal between the suction and pressure sides of the...

  This is a 1HP Seal & Impeller Kit for a Watkins 37334 Vendor Code# 4081 Pump with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Wavemaster 48 1.0HP Motor would be about 7-8.0 Amps on high speed at 230V or 11-12.0 Amps at...

This Connect Kit is an Air Bleeder barbed plug, 3/8" X 3/8" Barbed Coupler, 4" of 3/8" Tubing and Silicon sealer usually used on a Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up. I have seen these fittings in many...

This item is a 48 Frame Vico Wet End with 2" x 2" inlet and outlet that would measure about 3" across the threads and it has a 3.0HP impeller which would fit a motor that has 10.0-12.0 amps at 230V and there are no 115V motors this fits.. Pump to Motor...

This part is a Sta-Rite Dura-Jet Complete 2" X 2" Wet End that fits both 48 or 56 frame motors and would fit a 230V Pump that is 8.0 Amps or a 115V pump that is 12.0 Amps.. The 2" fitting actually measures about 3" Edge to Edge across the threads.. It...