Complete Wet Ends

This Item is a Wear Ring, fits LX 1431501-03 Wet End Only. It may have a Vendor Code 3536 on the LX Brand Pump. These pumps usually have the part number 1431501-03 on the label for the 3536 Version. NOTE: Do Not purchase this for any other brand except...

This 1.5 Horse Power 48 Frame Pump Wet End fits LX Jacuzzi or Sundance Brand 6500-090 , 6500-345 , 6500-357 , 6500-845 Pump Motors only that would be about 9.0 Amps at 230V or 14.0 Amps at 115v... These pumps usually have the part number WUA-150,...

This Wet End with Barb is a 2.5 Horse Power that fits Jacuzzi® Premium or Sundance® brand Hot Tubs only. The pumps this Wet End fits will have the part number 6500-352, 6500-365, 6500-367 or 6500-363 on the label along with WUA400-I or WAU400-II...

This Wet End is a 2.5 Horse Power that fits Jacuzzi® Premium or Sundance® brand Hot Tubs only. The pumps this Wet End fits will have the part number 6500-352, 6500-365, 6500-367 or 6500-363 on the label along with WUA400-I or WAU400-II. Note: You...

This complete pump and motor is a replacement for 36675-03.. This pump is a 115V or 230V, (1) Speed, 17.0Amp or 8.5Amp, 48 frame 2" x 2" XP2 pump and motor... The 2" inlet and outlet measure about 3" across the threads... Keep in mind if you choose this...

This part is a Pump Shaft Water Slinger designed to sling water away from the motor front bearing in case of a seal leak and it fits All Brands of Hot Tub Pumps..   This part goes on the shaft before you install the wet end.. 

This part is a Union Tee, Balboa Vico Ultima/UltraFlo, 1-1/2"fbt x 1"slip x 1"slip.. This part is usually found in a garden bathtub setup not a hot tub in your backyard..  The threaded Pump Union part measures 2 3/8" across the threads and the...

This part is a 3 5/8" Center to Center O-Ring only for a WUA500 or SWIM56-15 5 Horse Power 56 Frame Pump Wet End fits Power-Rite Guangdong LX Brand SWIM56-15 Pump Motors only. These pumps usually have the part number Swim56-15 or WUA500 on the...

This Kit is a Set of (4) Total Combination of the Two Standard Size 2" Heater or Pump Union Gasket (2) with a 2 1/2" Lip Center to Center and (2) with a 2 5/8" Lip Center To Center. The purpose of this Combo Kit is if you don't know...

This Kit is a Combination of the Two Standard Size 2" Heater or Pump Union Gasket (1) with a 2 1/2" Lip Center to Center and (1) with a 2 5/8" Lip Center To Center. The purpose of this Combo Kit is if you don't know which size you have...

This Kit is a Set of (2) NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this...

This part is a Stronger Pump Bleeder Barb that fits some Watkins Wavemaster XP2, XP2E, LX and others.. It is 1/4" Barb x 1/4"Npt and is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines....