Sundance Hot Tub Parts

This Impeller and Seal Kit is used ONLY in Intertek WTC50 Pumps Only. The impeller may have the number B432-01, B432-02, B432-03, B432-04, B432-05 on the back. The impeller measures about 3 5/8" across but the size can vary but this impeller is the...

Sundance and Jacuzzi Flow Switch for 2006-2009 models. Jacuzzi used this switch on all 400 Series models 2006-2009 and in various Sundance models, including in ground units. Includes the tee with mounted flow switch, 5 ft cable and box end connectors...

Transformer for Sundance and Jacuzzi based LX circuit boards. This 115/230 volt transformer has a step down voltage of 12 Volts. The purpose of this transformer is to energize the circuit board to power low voltage items like the processor, relay coils,...

This part is a O-Ring, Pump Housing Plug, JACUZZI, Pirahna/Theramax, 0.434"ID x 0.682"OD, .125"Cord Diameter.. Additional Information Outside Diameter .682 Inside Diameter .434 Type Standard Spa Brands Sundance/Jacuzzi

This part is an Adapter, Drain Plug, Sundance / Jacuzzi, 1/4" MPT x 3/8" Ribbed Barb, Stainless Steel, Less O-Ring.. Used on Various J-200, J-300, J-400, J-500, J-LX Series Spa Pump HeadsO-Ring is Required, Teflon Tape Not Used Click here for the...

This kit is an Ozonator UV Bulb for the Sundance and jacuzzi Spas ClearRay ozone generator. Bulb includes a wired 4 pin connector. Used from 2016 - current. Replaces 6473‐857  Replacement UV Sanitizer Bulb for 120v ClearRay Water Management...

This part is a Jacuzzi or Sundance Spa 3 7/8" Gasket found on Light Lenses, Jets and More The hole size is 3 1/8". This fits only Jacuzzi and Sundance Hot Tubs that fit these measurements. The reason they are replaced is due to extreme Chemical damage...

This part is a Wiring Adapter for a 4 5/32" Wide Jet: IX Jet Assembly with Integrated LED Light or a Waterfall..  For the jet that this adapter goes to Click this link: 4 5/32" Jet Assembly, Sundance, IX-J-400, w/Light & Wire Harness

This part is a Wet End, Circulation, TheraMax II, 1/15hp, 230v, 1-1/2" Side Discharge, Sundance , Jacuzzi, 02410512-2 or 6500-907.  The Model# on the pump this would fit would be 02410512-2 or 6500-907.. Note: There are variations to pumps with the...

This part is a Complete Wet End for a Sundance, TheraMax II, 6500-901 or 6500-902, 2.5HP, 230v, 56fr, 2"X 2" 11-12A with a 2" suction side and 2" pressure side which measures about 3" edge to edge. The amperage on the motore this would be on is about12...

This part is a Jacuzzi or Sundance Spa 4 1/4" Complete Light Assembly Kit. Lense, Green Cover, Blue Cover, Bulb Holder, Gasket and Nut..  The face size is 4 1/4" Some websites say 4 1/2" but ti is not. The hole size is 3 1/8". This fits only...

This part is a Jacuzzi or Sundance Spa 4 1/4" Light Assembly Kit , Lens, Gasket and Nut..  The face size is 4 1/4" Some websites say 4 1/2" but ti is not. The hole size is 3 1/8". This fits only Jacuzzi and Sundance Hot Tubs that fit these...