Aqua-Flo Impellers and Parts

This O-Ring is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...

This Face Plate O-Ring Is 4-3/4" Inside Diameter and is 1/8" Thick. It is found on Aqua-Flo 1 1/2" x 1 1/2" (Which Measures 2 3/8" Outside of the threads on the Sunction and Pressure Side of the Wet End) These Wet Ends used the names Flo-Master,...

This is a 3HP Seal and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor would be about 12.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct Aqua-Flo XP2 Impeller...

This is a 2.5HP Seal, (2) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.5HP Motor would be about 11.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct...

This is a 2.5HP Seal, (1) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.5HP Motor would be about 11.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct...

This is a 3HP Seal, (2) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor would be about 12.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct Aqua-Flo...

This is a 3HP Seal, (1) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor would be about 12.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct Aqua-Flo...

This is a 1/15th HP Impeller for an Aqua-Flo Circulation Pump 48 Frame Side or Center Discharge CMHP, CMCP and FMVP Series Wet End. This Impeller fits between the Face and the Volute of an Aqua-Flo CMHP, CMCP and FMVP Series Wet End. I would advise...

This part is an Aqua-Flo XP3 Pump 4.0HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4.0HP pump impeller to be on a 14 amp motor... Click here for the...

This part is an Aqua-Flo XP3 Pump 3.0HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 3.0HP pump impeller to be on a 12amp motor... Click here for the...

This part is an Aqua-Flo XP3 Pump 2.5HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 2.5HP pump impeller to be on a 10-12amp motor... Click here for...

This is a 4HP Seal, (2) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V. Note: The three things you need to know to get the correct Aqua-Flo...