Aqua-Flo Wet Ends Complete

Standard Pump Union Adapter Assembly With this adapter you can convert a 2" Threaded Pump Union whcih measures about 3" I.D. to a 1 1/2" threaded fitting which = 1 7/8" O.D. standard wet end. An O-Ring does come with this fitting but if you just needed...

This part is a Pump Bleeder Barb with O-Ring that is found on some Aqua-Flo Xp2 and Xp2e wet ends but is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part does come with the...

This is a 1.5HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 1.5HP Motor that has about 9.0 Amps on High Speed at 230V and 14.0 Amps at 115V. This Impeller fits between the Face and the Volute of...

This part is a 2 1/2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 2 1/2" Pump Union. The Pump Union Split Nut that measures about 3 3/4" on the outside and mounts to the existing Pump Union Body using 2...

This is a 1HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 1HP Motor that has about 8.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This Seal is a PS-3867 which is the Better - Viton Carbon Graphite version of the PS-200 Seal used Primarily in Aqua-Flo Wet Ends and Waterway "Viper" Wet Ends. It is 1 1/4" Across the back of the Spring Seal part that goes onto the Impeller and the...

This part is a 1 1/2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 1 1/2" Pump Union. The Pump Union Split Nut that measures about 2 7/8" on the outside and mounts to the existing Pump Union Body using 2...

This part is a 1 1/2" Slip X 1 1/2" Pump Union with Gasket or Oring that matches Union. See Pictures for measurements. The Union receives a 1 1/2" pipe or fitting on one side and then Screws to a 1 1/2" Wet...

This part is a 2 1/2" Pump Union Gasket Only for use with a 2 1/2" Pump Union that would measure about 3 5/8" Inside Threads. This gasket measures 3 1/4" O.D. x 2 3/8" I.D. and the lip is 2 7/8" center to center. This version is the 4th most...

NOTE: This gasket does not fit your Coleman SALUSPA DO NOT order it.. Click this link to see Saluspa Gaskets.. Saluspa This part is a Standard 1 1/2" Heater or Pump Union Gasket. The gasket is 2 3/8" across and fits unions that have a 1...

This part is a 2" Slip X 2" Threaded Pump Union with Gasket or O-ring that matches Union. The Union receives a 2" pipe or fitting on one side and then Screws to a 2" Wetend(Pump) Threaded Part on the other...

This part is a 2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 2" Pump Union. The Pump Union Split Nut that measures about 3" on the Inside of the Threaded Side and mounts to the existing Pump Union Body...