Wavemaster 9200 Complete Pumps

This Pump is a Perfect Replacement for a LX 0982601-03 2.5HP 11.0/3.5 Amp (2) Speed 56 Frame Complete Pump. It is about 7 1/4"" across the face of the pump, it measures about 7 3/8" from the bottom to the top of the pressure side of the volute, it...

This Pump is a Perfect Replacement for a LX 1431601-03 Pump it is a 3.0 Horse Power 12.0/3.5 Amp (2) Speed 56 Frame Complete Pump. It is about 7 1/4"" across the face of the pump, it measures about 7 3/8" from the bottom to the top of the pressure...

This is a 2.5HP Seal, (2) Bearings & Impeller Kit with a 2 1/8" Eye Width. This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081. Fits Some Watkins Hot Spring...

This is a 2.5HP Seal, (1) Bearing & Impeller Kit with a 2 1/8" Eye Width. This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081. Fits Some Watkins Hot Spring....

Watkins Vendor Code 4081 Older Style Wavemaster, 4000, 6000, 7000, 8000, 8200, 9000, 9200... 48Frame Pump Face O-Ring Only fits around the Face of this Pump Face... There are (2) Different versions of the Face plate O-Ring on the Xp2 Wet Ends.. The...

This Part is a 2 1/8" wear ring that is used between the impeller and the wet end face on Watkins Vendor Code # 4081, Wavemaster, 4000, 6000, 7000, 8000, 8200, 9000, 9200.. This wear ring serves as a seal between the suction and pressure sides of the...

This Pump is a Perfect Replacement for a LX 39578-03 Pump it is a 2.5 Horse Power 12.0/4.4 Amp (2) Speed 56 Frame Complete Pump. It is about 7 1/4"" across the face of the pump, it measures about 7 3/8" from the bottom to the top of the pressure...

This is a Watkins Wavemaster 9000 or 9200 2.5HP Seal Kit & Impeller with a 2 1/8" Eye Width. This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081...

As of 11/2024 Aqua-flo has started to send this pump with a capacitor bump in an odd spot that may affect your installation, see pic 2. In light of that we are now sending this pump assembly out as a separate 10.5 Amp motor and a genuine 2.5 HP XP2...

This Part is (1) NON-Standard 2" Heater or Pump Union Gasket with a 2 5/8" Center to Center Lip. The gasket is 2 7/8" across on the outside the inside diameter is about 2" and the lip that fits into the union is 2 5/8"...

This 1.0 Horse Power 10.3/3.8 Amp (2) Speed 48 Frame Complete Pump is a Watkins Vendor Code 3536 LX Brand Pump. These pumps usually have the part number 37334-03 on the label for a Watkins Version.  It is about 7 1/4"" across the face of the pump,...

This part is a Rubber Pump Motor Base Vibration Dampener for 48 and 56 frame pumps. Includes 4 soft 'washers' to isolate mounting screws from touching the motor base. This motor base mounting pad fits under any 48 frame pumps, and under most 56 frame...