Complete Wet End, Aqua-Flo ,XP2, 1.0HP, 2"x 2" , 48fr, fits Motors with 8.0A/230V 12.0A/115V
- SKU:
- HTP910416ER-000
- Shipping:
- Calculated at Checkout
-
Complete Wet End, Aqua-Flo ,XP2, 1.0HP, 2"x 2" , 48fr, fits Motors with 8.0A/230V 12.0A/115V
-
This is a chart you can use to determine which Aqua-Flo version you have..
-
Look at your wet end through bolt holes to determine if your wet end is a 48 or 56 frame. Keep in mind that your old wet end will not have both inserts so you need to measure and compare it to the charts..
-
Complete Wet End, Aqua-Flo ,XP2, 1.0HP, 2"x 2" , 48fr, fits Motors with 8.0A/230V 12.0A/115V
-
Complete Wet End, Aqua-Flo ,XP2, 1.0HP, 2"x 2" , 48fr, fits Motors with 8.0A/230V 12.0A/115V The Motor is not included...
-
Complete Wet End, Aqua-Flo ,XP2, 1.0HP, 2"x 2" , 48fr, fits Motors with 8.0A/230V 12.0A/115V
-
Complete Wet End, Aqua-Flo ,XP2, 1.0HP, 2"x 2" , 48fr, fits Motors with 8.0A/230V 12.0A/115V
Description
This part is a Complete 1HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 48 frame wet end for XP2 pumps. This wet end is used with a 48 frame motor that would have about 8.0 Amps on High Speed on a 230V motor or 12.0 Amps High Speed on a 115V 1/4" thru-bolt style motor. The motor used may be either a single or dual speed. The wet end may be rotated 90 degrees to change the discharge position. The complete wet end includes: the volute, seal, impeller, wear ring, suction cover, suction cover o-ring, drain plug, drain plug o-ring and suction cover screws.
If you need a barb for the front of your wet end where a small hose connects here are choices for those Barbs with or without sealer.. I always seal these with silicon Pipe tape does not work well on these fittings:
Barb Adapter, 3/8"b x 1/4"mpt, Pump Wet End Face fits Aqua-Flo & CMP
Barb Adapter, 3/8"b x 1/4"mpt, With Silicon Kit Pump Wet End Face fits Aqua-Flo & CMP
Note: You always base your choice of HP on the Amperage of the motor it is going on see the chart below.. a 48 frame motor measures about 5 1/2" across the motor and will have 1/4" heads on the thru-bolts and will measure about 5 3/16" between the thru-bolts in a cross pattern and 56 frame motor measures about 6 1/4" across the motor and will have 5/16" heads on the thru-bolts and will measure about 5 7/8" between the thru-bolts in a cross pattern..
Horsepower VS Amperage Chart
Pump to Motor Foot Types | 9 |
Motor Frame | 48 Frame Thru-Bolt |
Drain Plug Location | 4,6,9 o`clock |
Suction Auxillary Port | None |
Suction Style | Center |
Suction Connection (Physical Dimension) | 3-1/16"od |
Suction Connection Type | Male Buttress Thread (mbt) |
Suction Pipe Size | 2" |
Discharge Auxilary Port | None |
Discharge Style | Side |
Discharge Connection (Physical Dimension) | 3-1/16"od |
Discharge Connection Type | Male Buttress Thread (mbt) |
Discharge Pipe Size | 2" |
Horsepower | 1.0hp |
Manufacturer | AquaFlo/Gecko |
Pump Model | Flo-Master XP2 |
Manufacturer Impeller Number | 91694110 |
Volute Fastening Type | 8 Screws |
Volute/Sealplate Number | 92770705 |
3 Reviews
-
Complete wet end
Helped with determining the correct part and everything fit and matched up just fine. Very quick shipping too!
-
Worked
Appears to be a duplicate of original pump. If it lasts longer than original pump I will be extremely happy. Found Information your web site to be very helpful in selection of replacement pump.
-
Perfect match
Very happy with the wet end, if fit perfectly and was easy to replace. The motor and wet end work great. Looks like I may also have an issue with the display or control so I'll be contacting them again.