Aqua-Flo Impellers and Parts

This Kit is a Set of (4) Total Combination of the Two Standard Size 2" Heater or Pump Union Gasket (2) with a 2 1/2" Lip Center to Center and (2) with a 2 5/8" Lip Center To Center. The purpose of this Combo Kit is if you don't know...

This Kit is a Combination of the Two Standard Size 2" Heater or Pump Union Gasket (1) with a 2 1/2" Lip Center to Center and (1) with a 2 5/8" Lip Center To Center. The purpose of this Combo Kit is if you don't know which size you have...

This Kit is a Set of (2) NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this...

This O-Ring  is used on Aqua-Flo Pump Drain Plugs on Xp2, Xp2e, XP3 pumps and more..  Part Type    O-RingCross Section    3/32"Inside Diameter    7/16"id 

This kit is an Air Bleeder Barbed Plug Connect Kit that features a Barbed Plug that is 1/4" MPT x 3/8" Barb, (1) 3/8" x 3/8" Barbed Coupler, 4" of 3/8" clear tubing and Silicon sealer usually used on a Aqua-Flo and CMP Hot Tub Pump Faces to bleed the air...

This O-Ring is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...

This Face Plate O-Ring Is 4-3/4" Inside Diameter and is 1/8" Thick. It is found on Aqua-Flo 1 1/2" x 1 1/2" (Which Measures 2 3/8" Outside of the threads on the Sunction and Pressure Side of the Wet End) These Wet Ends used the names Flo-Master,...

In this Video The Spa Guy shows you how to identify what Impeller you need to replace your Aqua-Flo Xp2 or XP2e pump impeller... Save Save Save Save Save Save Save Save Save Save Save Save Save Save Save Save Save

This Face Plate O-Ring Is 5 1/8" Inside Diameter and is 1/8" Thick. It is found on Aqua-Flo 1 1/2" x 1 1/2" (Which Measures 2 3/8" Outside of the threads on the Sunction and Pressure Side of the Wet End) These Wet Ends used the names Flo-Master,...

This kit is a Air Bleeder barbed plug and Silicon sealer usually used on a Aqua-Flo and CMP Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands of Hot Tubs just compare the pictures and...

Aqua-Flo Xp2 6.1" or 6.3"and XP2e Flo-Master Pump Face O-Ring fits around the Face of a Xp2 Pump Face exclusively for An Aqua-Flo Xp2 pump which has 2" inlet and outlet which measures about 3" across the threads... There are (2) Different versions of...

This wear ring measures 2 3/8" inside Diameter and fits only 3.0HP Aqua-Flo XP2e and Xp3 Impellers.. If you have 1.5, 2.0, 2.5 or 4.0HP they require a different Wear Ring which measures 2 5/8" Inside Diameter.. Look at the chart in the photo section...