Pump Impellers

This is a XP2e 3.0HP Impeller.. The Impeller has a 2 3/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor would be about 12.0 Amps on high speed at 230V there are no 115V versions. Note: If your old impeller has a 2 3/8" Eye this is the...

This is a XP2e 2.5HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.5HP Motor would be about 11.0 Amps on high speed at 230V there are no 115V versions. See the links below for seals, bearing and other parts for...

This Kit is an 2HP Impeller for an Executive 48 Frame Wet End up to 2HP Motor and a 56 Frame Wet End 2 HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you...

This is a 2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 2HP Motor that has about 10.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This part is a face plate drain plug for Aqua-Flo pumps.. It does not come with an O-Ring you will find the link to that below.. Aqua-Flo Pump, Drain Plug, O-Ring Xp2, Xp2e, XP3, 7/16" ID, 3/32" Note: The Style of this part can vary but they will all...

This item is discontinued by the manufacturer but we have a similar product here: https://hottubpartsofamerica.com/tube-silicon-lube-ptfe-4oz/   U.S. SEALUBE is a water based formula specifically designed to lubricate rubber, making the installation...

This part is obsolete with no replacement.. Vico Ultima/Ultra Flo Pump Impeller 230V 8.0A or 115V 12.0AClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico. Rated at 1.0hp, it is used in an Ultima and/or Ultra Flo pump wet end, and...

You are buying (1) Bearing that fit some motors that are used in hot tubs, usually small 48 frame motors and some circulation pumps, this bearing is 15.9MM ID x 40MM OD. Some of the motors this fits are A.O.Smith/Regal Beloit, Century/Regal Beloit,...

This is a 3HP Impeller with a 2 1/8" Eye with 7/16" Vane Width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor which would have about 12.0A on high speed. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2...

This Pump is an Aqua-Flo Replacement Pump for the numbers 36746, 72194, 72197 with a Vendor Code 4081... This pump is a 48Frame 230V 2 Speed with a 2.0 HP Wet End that features a 2" x 2" inlet and outlet Wet End that measures about 3" across the threads....

This part is an Jacuzzi J Pump Impeller Wear Ring.. It measures about 1 15/16" ID and 2 7/16" to the outermost OD..  Fits the following pumps: Cygnet Series - All Horsepowers J, JCM, K and KM Series - All Horsepowers L, LC, LCUN2,...

This part is a Pump Bleeder Barb with O-Ring that is found on some Aqua-Flo Xp2 and Xp2e wet ends but is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part does come with the...