Pump Impellers

This part is a 2HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0122 cast into the back and will measure about 3 3/4" wide with an eye width of 1 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This part is a 3.0HP Power-Right Pump Impeller that would be found on a motor with about 12.0 Amps at 230V.. Closed face impeller made for the Power-Right 3.0ohp/6.0thp spa pump. Rated at 3.0hp, it is used in the Power-Right 9089X, 9094X, 9121X, PRC504...

This part is a 2.5HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0123 cast into the back and will measure about 3 3/4" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 2.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 2.0hp (or greater) thru bolt motor. Shaft seal sold...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 3.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 3.0hp (or greater) thru bolt motor. Shaft seal sold...

Vico/Balboa Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico/Balboa. Rated at 4.0hp, it is used in an Ultimax pump wet end, and must be installed on a 4.0hp (or greater) thru bolt motor. Click the below links for the...

This part is a Wear Ring that measures 2 5/8" inside Diameter and fits some Aqua-Flo XP2e and Xp3 Impellers except the 3.0HP Xp2e Impeller... That Impeller requires a different Wear Ring which measures 2 3/8" Inside Diameter.. Look at the chart in the...

 Vico/Balboa Ultima Ultra Flo or Ultra Jet Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico. Rated at 3.0hp,which is between 10 and 12 Amps.. it is used in an Ultima, Ultra Jet and/or Ultra Flo pump wet end, and...

Vico Ultima, Ultra Flo Pump Impeller for a 2HP Motor which would have an Amperage of around 10 Amps on High Speed... Closed face impeller made for the Ultima and Ultra Flo spa pumps by Vico. Rated at 2.0hp, it is used in an Ultima and/or Ultra Flo pump...

This Wear Ring only fits Waterway Executive 1, 2, or 3HP Impellers for a 48 or 56 Frame Pump Wet Ends and measures 1-1/16" thick from front to back... If you have a Waterway Executive 4 or 5 Horsepower Wet End it will require a different wear ring that...

Seal Plate for Vico Ultima pumps. Material Type    PlasticVolute to Seal Plate Mounting Type    4 Bolts 4 NutsVolute to Seal Plate Hole Spacing    4-3/8"Seal Plate to Motor Mounting Type    48...