Aqua-Flo Wet Ends Complete

This Tool is a Die that fits all American made Hot Tub Pump shaft threads.. This fits Hot Tub Pumps only in these brands.. Waterway, Aqua-Flo, Sta-Rite, Vico and Power-Right.. Note: This will NOT for LX Intertek Motor Shaft... 

This kit is an Air Bleeder Barbed Plug Connect Kit that features a Barbed Plug that is 1/4" MPT x 3/8" Barb, (1) 3/8" x 3/8" Barbed Coupler, 4" of 3/8" clear tubing and Silicon sealer usually used on a Aqua-Flo and CMP Hot Tub Pump Faces to bleed the air...

This part is a Complete CMHP 1/15th HP Aqua-Flo 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Side discharge 48 frame wet end for CMHP pumps. This wet end is used with a 48 frame motor that would have about .6 Amps on High Speed on a...

This O-Ring is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...

This Face Plate O-Ring Is 4-3/4" Inside Diameter and is 1/8" Thick. It is found on Aqua-Flo 1 1/2" x 1 1/2" (Which Measures 2 3/8" Outside of the threads on the Sunction and Pressure Side of the Wet End) These Wet Ends used the names Flo-Master,...

This Kit is a 3/8" Tubing Connection Kit for 3/8" Plumbing repairs where you are connecting old 3/8" Clear Tubing that measures about 1/2" OD between a cut air control line and the 3/8" Barb on an Air Manifold or Jet Body Air connection.. The kit...

This is a 1/15th HP Impeller for an Aqua-Flo Circulation Pump 48 Frame Side or Center Discharge CMHP, CMCP and FMVP Series Wet End. This Impeller fits between the Face and the Volute of an Aqua-Flo CMHP, CMCP and FMVP Series Wet End. I would advise...

You are buying a Kit that features (1) PS-200 Seal and (2) Bearings that fit most motors that are mated to Aqua-Flo Pump Wet Ends as well as Waterway " Viper" Wet Ends, The Professor silly Juice to seal the seal. This Seal is used in Most Aqua-Flo...

This Part is (1) NON-Standard 2" Heater or Pump Union Gasket with a 2 5/8" Center to Center Lip. The gasket is 2 7/8" across on the outside the inside diameter is about 2" and the lip that fits into the union is 2 5/8"...

This Face Plate O-Ring Is 5 1/8" Inside Diameter and is 1/8" Thick. It is found on Aqua-Flo 1 1/2" x 1 1/2" (Which Measures 2 3/8" Outside of the threads on the Sunction and Pressure Side of the Wet End) These Wet Ends used the names Flo-Master,...

This part is a Complete XP2e 6.3” 1.5HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 9.0 Amps on High Speed on a 230V...

This part is a Complete XP2e 6.3” 3.0HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 12.0 Amps on High Speed on a...