Complete Wet Ends

Waterway Hi-Flo Wet EndSide discharge, 2"mbt suction/discharge, 48 frame wet end for the Waterway Hi-Flo pump. This wet end is used with a 11.0 Amp 2.0hp, 48 frame, thru-bolt style motor. The motor used may be either a single or dual speed. The wet end...

This Wet End is a 2" x 2" 1.5HP 48 or 56 frame Ultimax Vico® that would normally be found an a 230V pump with 9.0 Amps High speed or 14.0 Amps at 115v..  This side discharge, 2" x 2" mbt which would measure about 3" edge to edge on the threads,...

This Kit Fits Watkins, Vendor #4081, Wavemaster Pumps found under the name Wavemaster. This Kit Features (2) Bearings, (1) Seal and (1) 1/2oz Tube of The Professor's Silly Juice a Specially Formulated for Hot Tubs Silicon Sealer.   Note: Watkins...

This kit Fits Watkins, Vendor #4081, Wavemaster XP2 Pumps found under the name Wavemaster with the Vendor Code 4081 only.. Features (1) Seal for XP2 Pumps on Hotspring Watkins Hot Tubs, Seal Install Tool and (1) 1/2oz Tube of The Professor's Silly Juice...

This Kit is a Universal Air Bleeder Connect Kit with (1) 1/4" Mpt X 3/8" Barb Plug, (1) 3/8" x 3/8" Barb Coupler, (4") of 3/8" Clear Tubing and Silicon sealer usually used on Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I...

This kit is an Air Bleeder Barbed Plug Connect Kit that features a Barbed Plug that is 1/4" MPT x 3/8" Barb, (1) 3/8" x 3/8" Barbed Coupler, 4" of 3/8" clear tubing and Silicon sealer usually used on a Aqua-Flo and CMP Hot Tub Pump Faces to bleed the air...

This kit is a Set of (2) Air Bleeder barbed plugs,(2) 3/8" x 3/8" Barb couplers, (2) 4" long pieces of 3/8" Tubing and Silicon sealer usually used on a Dynasty Hot Tub with Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up...

This kit is a Set of (2) Air Bleeder barbed plugs and Silicon sealer usually used on a Dynasty Hot Tub with Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands just compare the...

This Part is a Barbed Bleeder Barb with O-Ring that fits New Style 48 or 56 Frame WUA Intertek LX Brand Pump Wet End that uses a fine thread bleeder plug.. Watch the video for instruction on how to install this part and also how to...

This part is a Complete CMHP 1/15th HP Aqua-Flo 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Side discharge 48 frame wet end for CMHP pumps. This wet end is used with a 48 frame motor that would have about .6 Amps on High Speed on a...

This O-Ring is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...

NOTE: This Part will Fit Sundance® or Jacuzzi® Tubs with a Guangdong LX Wet End if you replace the entire Wet End for internal parts of the wet end you already have click here Jacuzzi® & Sundance® LX...