Pump Wet Ends and Related Parts

 This part is the slinger found between the impeller and wet end and the shaft going into the pump motor bearing area and is designed to sling water away from the bearing in case of a seal leak at the wet end.. Note: It has to be placed on the motor...

You are buying (1) Bearing that fit some motors that are used in hot tubs, usually small 48 frame motors and some circulation pumps, this bearing is 15.9MM ID x 40MM OD. Some of the motors this fits are A.O.Smith/Regal Beloit, Century/Regal Beloit,...

This is a 3HP Impeller with a 2 1/8" Eye with 7/16" Vane Width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor which would have about 12.0A on high speed. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2...

This Drain Plug fits Vico Ultima and Ultimax and comes without O-Ring.. If you need the O-Ring click the Link: Pump, Drain Plug, O-Ring, will fit most Drain Plugs

This Pump is an Aqua-Flo Replacement Pump for the numbers 36746, 72194, 72197 with a Vendor Code 4081... This pump is a 48Frame 230V 2 Speed with a 2.0 HP Wet End that features a 2" x 2" inlet and outlet Wet End that measures about 3" across the threads....

Standard Pump Union Adapter Assembly With this adapter you can convert a 2" Threaded Pump Union whcih measures about 3" I.D. to a 1 1/2" threaded fitting which = 1 7/8" O.D. standard wet end. An O-Ring does come with this fitting but if you just needed...

This part is an Jacuzzi J Pump Impeller Wear Ring.. It measures about 1 15/16" ID and 2 7/16" to the outermost OD..  Fits the following pumps: Cygnet Series - All Horsepowers J, JCM, K and KM Series - All Horsepowers L, LC, LCUN2,...

This part is a Bleeder Barb that is 3/8" barb x 1/4" Threaded MPT fitting fits Wet End Face Bleeder Plug Holes to attach a Bleeder Line it fits Waterway Executive 48 & 56 Frame Parts & Wetends, Power-Right 9089X, 9094X,...

This part is a Pump Bleeder Barb with O-Ring that is found on some Aqua-Flo Xp2 and Xp2e wet ends but is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part does come with the...

This part is an O-Ring that is a square style.. It fits Piranha "A", Thera-Flo, Thera-Max, Bracketless, all found on Jacuzzi, Sundance, Hotspring and other brands as well...Part Type    Square RingO Reference Number  ...

This Kit is an 5HP Impeller for an Executive 48 Frame Wet End up to 5HP Motor and a 56 Frame Wet End 5HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

This is a 1.5HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 1.5HP Motor that has about 9.0 Amps on High Speed at 230V and 14.0 Amps at 115V. This Impeller fits between the Face and the Volute of...