Pump Wet Ends and Related Parts

This part is a Pump Face for a Vico Ultima Side Discharge wet end that is 2" which measures about 3" edge to edge across the threads.. The Seal Kits for this pump can be found here: Vico Seals 201 The other parts for this pump can be found here: Ultima...

This part is a Complete FMHP 1.0HP Aqua-Flo 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Side discharge 48 frame wet end for FMHP pumps. This wet end is used with a 48 frame motor that would have about 8.0 Amps on High Speed on a 230V...

This part is a 2.5HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0123 cast into the back and will measure about 3 3/4" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This part is a 2.0HP Sta-Rite Dura-Jet Complete 2" X 2" Wet End that fits both 48 or 56 frame motors and would fit a 230V Pump that is 10.0 Amps or a 115V pump that is 16.0 Amps.. The 2" fitting actually measures about 3" Edge to Edge across the threads....

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 2.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 2.0hp (or greater) thru bolt motor. Shaft seal sold...

This part is a Complete XP2e 6.3” 4.0HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 14.0 Amps on High Speed on a...

This part is a Complete FMHP 2.0HP Aqua-Flo 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Side discharge 48 frame wet end for FMHP pumps. This wet end is used with a 48 frame motor that would have about 10.0 Amps on High Speed on a...

Jacuzzi J-Series Wet End Kit Bottom Suction, center discharge, 2"mjt, 48 frame wet end by Jacuzzi/Carvin. This wet end is used with a 1.0hp, 48 frame, thru-bolt style motor. The motor used may be either a single or dual speed. The complete wet end...

This part is no longer available you can only get this with a complete wet end.. This part is a Face Plate with Drain Plugs and Face O-Ring that fits Aqua-FLO XP2E wet ends only on the back of the face where the wear ring will touch will measure about...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 3.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 3.0hp (or greater) thru bolt motor. Shaft seal sold...

Vico/Balboa Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico/Balboa. Rated at 4.0hp, it is used in an Ultimax pump wet end, and must be installed on a 4.0hp (or greater) thru bolt motor. Click the below links for the...