Pump Wet Ends and Related Parts

This part is obsolete you must choose a complete wet end..  Click this link for Xp2 Wet Ends.. XP2 and XP2e Aqua-Flo Complete Wet Ends This part is the Volute or the back part of a 48 Frame Aqua-Flo XP2 or XP2e Wet End.. We offer the entire wet...

This part is an Impeller for a Sta-Rite DuraJet DJ Wet End that would be called 1.0hp-1.5HP, your motor should be 8.0-9.0Amp at 230V or 16.0 Amps at 115V.. The number on the back of the impeller will be 17400-0021 or 17400-0121 if you have a number on...

This impeller is no longer avaialve from the manufacturer but the one at this link wil work in its place: Impeller, Aqua-Flo, XP3, 4.0hp, For XP3 Pump 2 1/2" x 2 1/2" Wet End This part is a Waterway Viper Pump 4.0 Impeller exclusively for A Waterway...

This Impeller is obsolete but there is an Impeller that will work but there is only one choice and it will look different than your old impeller: Impeller, Vico Ultima Ultra Jet Flo,4...

This Wet End is a 2" x 2" 4.0HP 48 or 56 frame Ultimax Vico® that would normally be found an a 230V pump with 14.0 Amps High speed there are no 115v versions of this wet end..  This side discharge, 2" x 2" mbt which would measure about 3" edge...

Balboa / Sta-Rite Dura-Jet wetend in 3HP. Also known as the DJ this high flow side discharge wetend can be mounted to 48 or 56 frame motors. This side discharge model has 2" unions that will measure 3" across the male threads. The barb fittings on this...

You are buying a 2 HP 48 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Screws, Volute, Impeller, Seal, Face and the Wear Ring. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3...

This part is a Complete XP2e 6.3” 2.5HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 11.0 Amps on High Speed on a...

Vico/Balboa Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico/Balboa. Rated at 2.0hp,which would be 8-10.0 Amps.. it is used in an Ultimax pump wet end, and must be installed on a 2.0hp (or greater) thru bolt motor...

Tnei part is no longer available you can only order the complete wet end found Here: Wet End, Waterway, Uni-Might, Iron-Might, 1.0HP, 1-1/2", 48 frame, 1.4A/115v Waterway Iron Might Circulation Pump Impeller for 1/8HP Pump Closed face impeller made...

This Kit is an 1HP Impeller for an Executive 48 Frame Wet End up to 1HP Motor and a 56 Frame Wet End 1HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

The Waterway center discharge wet end has been discontinued and replaced with the E-Series Center Discharge wet end by the manufacturer. Please be sure which wet end you have as the parts are not interchangeable. The easiest way to identify which wet end...