Wavemaster 8000 Complete Pumps

This part is a (4) Bolt head Screws and Washer Kit for 48 or 56 frame pumps used to mount pump motors down on wood based hot tubs. . Includes  (4) Screw head 1 1/8" Screws and (4) Washers.  Note: Rubber mount not included in this listing it can...

This part is a Rubber Pump Motor Base Vibration Dampener with (4) Bolt head Screw and Washer Kit for 48 and 56 frame pumps. Includes 4 soft 'washers' to isolate mounting screws from touching the motor base along with (4) Screw head 1 1/8" Screws and...

This part is a Stronger Pump Bleeder Barb that fits some Watkins Wavemaster XP2, XP2E, LX and others.. It is 1/4" Barb x 1/4"Npt and is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines....

This part is a Pump Bleeder Barb for some Watkins Wavemaster LX Pumps and others.. It is 1/2" Barb x 1/4"Mpt and is used with an unusually large bleeder line.. The line is 1/2" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This...

This is an Aqua-Flo 39577 2.0HP Seal Kit & Impeller with a 2 1/8" Eye Width... This Impeller fits between the Face and the Volute of a XP2 Wet End found on some pumps with Vendor Code 4081. Impeller Type   Closed Face Impeller Diameter...

This part is a Pump Bleeder Barb fit some Watkins Wavemaster LX Pumps and others.. It is 1/2" Barb x 1/4"Mpt and is used with an unusually large bleeder line.. The line is 1/2" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part...

This part is a Pump Bleeder Barb fits some Watkins Wavemaster XP2, XP2E, LX and others.. It is 1/4" Barb x 1/4"Mpt and is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part...

This is a Watkins Wavemaster 8000 or 8200 2.0HP Seal, (2) Bearing & Impeller Kit with a 2 1/8" Eye Width... This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081...

This is a Watkins Wavemaster 8000 or 8200 2.0HP Seal, (1) Bearing & Impeller Kit with a 2 1/8" Eye Width... This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081...

Watkins Vendor Code 4081 Older Style Wavemaster, 4000, 6000, 7000, 8000, 8200, 9000, 9200... 48Frame Pump Face O-Ring Only fits around the Face of this Pump Face... There are (2) Different versions of the Face plate O-Ring on the Xp2 Wet Ends.. The...

This Part is a 2 1/8" wear ring that is used between the impeller and the wet end face on Watkins Vendor Code # 4081, Wavemaster, 4000, 6000, 7000, 8000, 8200, 9000, 9200.. This wear ring serves as a seal between the suction and pressure sides of the...

This Part is (1) NON-Standard 2" Heater or Pump Union Gasket with a 2 5/8" Center to Center Lip. The gasket is 2 7/8" across on the outside the inside diameter is about 2" and the lip that fits into the union is 2 5/8"...