Pumps and Related Parts

This pump is a Wow High Performance Pump with 1 1/2" x 1 1/2" connections that measure about 2 3/8" across the threads.. It is a .50 HP 115V 5.5 Amp pump with an Air Switch and Cord.. It also has 3/8" barbs that are optional to use and need to be drilled...

3.0 HP impeller for the Waterway EX2 pumps assemblies. This impeller is normally found on motors with a 10.7-12.0 amp motor and fits between the Face and the Volute of an EX2 Wet End. I would advise replacing the Seal when you replace the Impeller. The...

Single speed 48 frame spa motor rated at 1.5 HP. This dual voltage single speed motor can run at 115 or 230 volts. The amp rating on this motor is 7.7 amps at 230 volts and 15.4 amps at 115 volts. This thru bolt motor will fit any North American wetend...

This pump has been on an extended back order and we have no current ETA. If you would like an alternative, which is what this pump was modeled after, see this pump here: Balboa / Vico Power WOW, .05 HP. 115 Volts, 1-1/2" Union   LX WCA50 1/2 HP pump...

This Jet Pump is found from the factory in many hot tubs and will be an easy installation for people who are handy.   This pump is a new release from Aqua-Flo designed to be a less expensive replacement for Aqua-Flo XP2e  This pump is a...

This Jet Pump is found from the factory in many hot tubs and will be an easy installation for people who are handy.   This pump is a 56 frame XP2e 3.0HP 230V Side Discharge wet end with a 2" suction side and 2" pressure side which measures about...

US Motors / Nidec 1.0 HP motor, 115 volts, 2 speed with no top mounted capacitor. This 10.3 amp 48 frame motor can be used with many brands of pumps and wetend. Some brands this motor will fit are Waterway, Aqua-Flo, Vico, Balboa, Sta-rite and many more...

Pump union used on Dreammaker spas, also known as a hot stick. Easily identified by its red body and white nut. This union helps to create friction when the water rushes past it, aiding Dreammaker models that don't use a heater in getting hot faster. The...

This part is a (4) Bolt head Screws and Washer Kit for 48 or 56 frame pumps used to mount pump motors down on wood based hot tubs. . Includes  (4) Screw head 1 1/8" Screws and (4) Washers.  Note: Rubber mount not included in this listing it can...

This part is a Rubber Pump Motor Base Vibration Dampener with (4) Bolt head Screw and Washer Kit for 48 and 56 frame pumps. Includes 4 soft 'washers' to isolate mounting screws from touching the motor base along with (4) Screw head 1 1/8" Screws and...

This part is a LX Pump WUA500 2 1/2" Union 11/64" Thick 3 1/8" Center to Center O-Ring World's Finest Pump Union. The O-Ring is 3 5/8" Center to Center across and 11/64" Thick where the standard O-Ring is about 1/8" Thick. This fits LX Pump unions...

This pump is a Complete Pump, Aqua-Flo, Maelstrom, 3.0HP, 230v, 56fr, 2"X 2" 1 or 2 Speed 12A with a 2" suction side and 2" pressure side which measures about 3" edge to edge. The amperage is 12 Amps on High Speed and 3.5 Amps on Low making it a 3.0...