Pumps and Related Parts

  This is a 1HP Impeller with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.0HP Motor would be about 8.0 Amps on high speed at 230V or 12.0 Amps at 115V.   This Impeller fits between the Face and the...

This is a 230V Waterway Tiny Might Circulation Pump that is 1" x 1" which measures about 1 7/8" to the outside of the threads. It is high in efficiency and low on power use. Tiny Might packs a not-so-tiny punch. The Tiny Might offers you a great low flow...

This 2HP Impeller fits a Jacuzzi/Carvin Wet End only and would be found on a motor that is about 16.0 Amps on a 115V motor or 10.0 Amps on a 230V motor..... It can be found under the Name Thera-Max or Thera-Flo and is found on Jacuzzi Premium J Series...

This part is a Wear Ring for a Hi-Flo Impeller found in Waterway Hi-Flo pumps only.. The Inside Diameter of the wear ring is 1 13/16"...

This parts is an Executive 2" Threaded Face plate assembly (Which will measure about 3" Across the Threads) less the O-rings, Screws, Bleeder Plugs and other hardware needed to attach it to the volute..There is another version of the face with a 2 1/2"...

This Listing is for a Waterway Executive 16.4 Amp 56fr 2 Speed 230V 5 HP 2" X 2" Pump. Your sticker may say 5-6HP. This unit features a 2" X 2" Executive Wet End that can be moved from the 12 O'clock position to the 3, 6, or 9 O'clock position and a...

This part is a Start Capacitor, 64-77 MFD, 250v, 1-7/16" Wide x 2-3/4" Tall.. Capacitor Type Motor Start Motor Brand A.O.Smith/Regal Beloit, Century/Regal Beloit, Franklin Electric, General Electric Microfarad Rating 64-77 mfd Motor Parts...

This part is a Impeller, Jacuzzi, J Pump, 1.0hp, 48FR, J Series, JCM Series, K Series, KM Series.. This is found on a Wet End that has a face like I show in the Photo Section only..  Impeller Type Closed Face Impeller Diameter...

Waterway Hi-Flo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 1.5hp, it is used in a Waterway Hi-Flo pump wet end, and must be installed on a 1.5hp (or greater) thru bolt motor. Shaft seal...

This Jet Pump is found from the factory in many hot tubs and will be an easy installation for people who are handy.   This pump is a 56 frame XP2e 3.0HP 230V Side Discharge wet end with a 2" suction side and 2" pressure side which measures about...

This impeller fits a Universal CMP Brand 3HP Wet End only and it requires a Special Seal that you will find a link to below.. This impeller may also have any of the following manufacturer part numbers stamped on the back: 27203-300-300, 27203-000-300,...

This part is a Complete 2HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 48 frame wet end for XP2 pumps. This wet end is used with a 48 frame motor that would have about 10.0 Amps on High Speed on a 230V motor or 16.0...