Pumps and Related Parts

// This pump is hard to get sometimes this is possible replacement for this pump: Pump, Circulation, LX, WE-14, 230v, 1-1/2"mbt, 4ft Cord This 230V Laing E-14 circulation pump is compact and lightweight, less than 5 lbs. The E14 consumes...

You are buying a 1" FTB X 3/4" Barb Pump Union with O-ring that matches the Union.The Union receives a 3/4" Inside Diameter Hose which measures about 1" on the outside and then Screws to a 1" Wetend (Pump) Threaded Part on the other side the threads will...

This part is a 2.5HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0123 cast into the back and will measure about 3 3/4" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This part is a 2.0HP Sta-Rite Dura-Jet Complete 2" X 2" Wet End that fits both 48 or 56 frame motors and would fit a 230V Pump that is 10.0 Amps or a 115V pump that is 16.0 Amps.. The 2" fitting actually measures about 3" Edge to Edge across the threads....

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 2.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 2.0hp (or greater) thru bolt motor. Shaft seal sold...

This part is a Complete XP2e 6.3” 4.0HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 14.0 Amps on High Speed on a...

This Pump is a 1 1/2" Side Discharge x 1 1/2" pump which measures about 2 3/8" across the threads edge to edge. This pump is a 115V and we do offer this same pump in a 230V verison ASP34-270-1055 click on the number for the other pump.  The Iron...

Terminal Board Cover

This part is a Complete FMHP 2.0HP Aqua-Flo 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Side discharge 48 frame wet end for FMHP pumps. This wet end is used with a 48 frame motor that would have about 10.0 Amps on High Speed on a...

Jacuzzi J-Series Wet End Kit Bottom Suction, center discharge, 2"mjt, 48 frame wet end by Jacuzzi/Carvin. This wet end is used with a 1.0hp, 48 frame, thru-bolt style motor. The motor used may be either a single or dual speed. The complete wet end...

This pump is a Pump, Waterway Executive, 5.0hp, 230v, 2-spd, 56fr, 2-1/2" x 2", OEM This is an unusual pump meaning the suction side is called 2 1/2" and measures about 3 5/8" Across the threads and the Pressure Side is 2" and measures about 3"...