Pumps and Related Parts

You are buying a 1" FTB X 3/4" Barb Pump Union with O-ring that matches the Union.The Union receives a 3/4" Inside Diameter Hose which measures about 1" on the outside and then Screws to a 1" Wetend (Pump) Threaded Part on the other side the threads will...

This part is a 2.5HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0123 cast into the back and will measure about 3 3/4" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This part is a 2.0HP Sta-Rite Dura-Jet Complete 2" X 2" Wet End that fits both 48 or 56 frame motors and would fit a 230V Pump that is 10.0 Amps or a 115V pump that is 16.0 Amps.. The 2" fitting actually measures about 3" Edge to Edge across the threads....

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 2.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 2.0hp (or greater) thru bolt motor. Shaft seal sold...

This part is a Complete XP2e 6.3” 4.0HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 56 frame wet end for XP2e pumps. This wet end is used with a 56 frame motor that would have about 14.0 Amps on High Speed on a...

This Pump is a 1 1/2" Side Discharge x 1 1/2" pump which measures about 2 3/8" across the threads edge to edge. This pump is a 115V and we do offer this same pump in a 230V verison ASP34-270-1055 click on the number for the other pump.  The Iron...

Terminal Board Cover

This part is a Complete FMHP 2.0HP Aqua-Flo 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Side discharge 48 frame wet end for FMHP pumps. This wet end is used with a 48 frame motor that would have about 10.0 Amps on High Speed on a...

Jacuzzi J-Series Wet End Kit Bottom Suction, center discharge, 2"mjt, 48 frame wet end by Jacuzzi/Carvin. This wet end is used with a 1.0hp, 48 frame, thru-bolt style motor. The motor used may be either a single or dual speed. The complete wet end...

This pump is a Pump, Waterway Executive, 5.0hp, 230v, 2-spd, 56fr, 2-1/2" x 2", OEM This is an unusual pump meaning the suction side is called 2 1/2" and measures about 3 5/8" Across the threads and the Pressure Side is 2" and measures about 3"...

This pump is a 115V 48 Frame 2" X 2" Waterway Executive (2) Speed 1.5HP 13.3Amp on High and 4.1A on Low..  The Pressure and Suction sides measure about 3" edge to Edge across the threads..  The Waterway Executive 48 pump is thermally...