Pumps and Related Parts

CAT: BN35SS MODEL: 186886 TYPE: CS FR: R 48 Y HP: 1.5 SF: 1.0 PH: 1 HZ: 60 RPM: 3450 ROT: CCWPE VOLTS: 230/115 AMPS: 8.0/16.0 MAX AMPS: SF AMPS: - TIME: CONT ENCL: ODP THERMALLY PROTECTED FORM: PHM CODE: G INSUL CLASS: B AMB.: 40¡C12 & 3 OÕclock Conduit...

This pump is a Wow High Performance Pump with 1 1/2" x 1 1/2" connections that measure about 2 3/8" across the threads.. It is a 1.0HP 115V 9.0Amp 1.0HP pump with an Air Switch and Cord.. This Vico-Ultrajet range of Hydro-Massage Whirlpool Pumps have...

This Kit is an 1HP Impeller for an Executive 48 Frame Wet End up to 1HP Motor and a 56 Frame Wet End 1HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

This pump is a 56 frame Motor with a Vico Side Discharge Wet End with 2" Suction and Pressure Threaded fitting that measure about 3" from edge to edge on the threads. This is a 2 Speed pump and the Amerage is 8.8 on high speed and 3.0 on low speed which...

The Waterway center discharge wet end has been discontinued and replaced with the E-Series Center Discharge wet end by the manufacturer. Please be sure which wet end you have as the parts are not interchangeable. The easiest way to identify which wet end...

This part is a 2HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0122 cast into the back and will measure about 3 3/4" wide with an eye width of 1 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This part is a Complete Flo-Master FMCP 1.5HP Aqua-Flo 1-1/2" x 1-1/2" ( Which measures about 2 3/8" Across the Threads) Center discharge 48 frame wet end for 48FR pumps. This wet end is used with a 48 frame motor that would have about 9.0 Amps on High...

Start Capacitor1-7/16"dia x 2-3/4"hgt

This Pump is a 48Frame 230V 2 Speed with a 2.0 HP Wet End that features a 1 1/2" x 1 1/2" inlet and outlet Wet End that measures about 2 5/16"" across the threads...  High speed Amperage is 8.5 and low speed is 2.8 Amps..   Complete Pump...

You are buying a 3 HP 56 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Screws, Volute, Impeller, Seal, Face and the Wear Ring. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3...

This item is a 1/2" Air Bleeder Plug with Fine threads that can be found on the Newer style of a Sta-Rite Dura-Jet DJ Series Wet ends only.  If you need the O-ring for this plug only Click Here: Sta-Rite Pump, New Style Drain...

This Pump is a 1 1/2" Side Discharge x 1 1/2" pump which measures about 2 3/8" across the threads edge to edge. This pump is a 115V and we do offer this same pump in a 230V verison ASP34-270-1050 click on the number for the other pump. The...