Pumps and Related Parts

You are purchasing a 1HP Impeller, (1) Standard Bearing and 1000 Seal with Silicon and a Seal Install Tool that fits an Executive 48 Frame Wet End up to 2HP Motor and a 56 Frame Wet End 1HP Motor. This Impeller fits between the Face...

You are buying a Kit that features (1) PS-201 Seal and (2) Bearings that fit most motors that are mated to Vico, Sta-Rite, Dura-Jet and Power Right Pump Wet Ends and The Professor's Silly Juice to seal the seal. This Seal is used in Most Vico,...

Half Union Fitting Complete Set... The Threaded side measures about 3" Inside and the Slip Glue end measures about 1 7/8" Inside Diameter for a 1 1/2" fitting to glue inside or 2 2/3" Outside Diameter for a 2" fitting to glue on the outside....

This 1 Horse Power 10.3/3.8 Amp (2) Speed 48 Frame Complete Pump is a Guangdong LX Brand Pump. These pumps usually have the part number 48WUA1001C-II on the label for a Watkins Version. Watch the video for instruction on how to Identify...

This is a 1/15th HP Impeller for an Aqua-Flo Circulation Pump 48 Frame Side or Center Discharge CMHP, CMCP and FMVP Series Wet End. This Impeller fits between the Face and the Volute of an Aqua-Flo CMHP, CMCP and FMVP Series Wet End. I would advise...

This 90 Tee Glue Kit is exclusively for HotSpring Hot Tubs made by Watkins and can be found under the name Hotspring, Solana, Tiger River, Caldera... This Item is the 90 Ell found on the pressure side of a Laing pump with a 3/8" bleeder line...

This part is an Aqua-Flo XP3 Pump 4.0HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4.0HP pump impeller to be on a 14 amp motor... Click here for the...

This part is an Aqua-Flo XP3 Pump 3.0HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 3.0HP pump impeller to be on a 12amp motor... Click here for the...

This part is an Aqua-Flo XP3 Pump 2.5HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 2.5HP pump impeller to be on a 10-12amp motor... Click here for...

This pump is a 115V (2) Speed 10.5 High and 3.2A Low Speed 48 frame 2" x 2" XP2 pump and motor... The 2" inlet and outlet measure about 3" across the threads... Keep in mind if you choose this high amperage pump and have a tub with a wall style 115V plug...

Waterway Hi-Flo Wet EndSide discharge, 2"mbt suction/discharge, 48 frame wet end for the Waterway Hi-Flo pump. This wet end is used with a 12.0 Amp 3.0hp, 48 frame, thru-bolt style motor. The motor used may be either a single or dual speed. The wet end...

This part is a Wear Ring that only fits Guangdong LX or LP Impellers for a 48 or 56 Frame Pump Wet Ends and measures 3/4" thick from front to back... WUA Pumps.. Note: When Replacing some original LX Pump faces the wear ring was built into the face....