Aqua-Flo Impellers and Parts

This part is a Set of (2) 2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 2" Pump Union. The Pump Union Split Nut that measures about 3" on the Inside of the Threaded Part and mounts to the existing Pump...

This Seal is The (BEST) Upgraded Salt Resistant Silicon Carbide Version a PS-200 Seal used Primarily in Aqua-Flo Wetends but is found in Waterway " Viper" & "EX2" Wetends and some others as well.. Silicon Carbide’s exceptional wear and...

This is a XP2e 1.5HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor would be about 9.0 Amps on high speed at 230V or 14.0 Amps on High at 115V. See the links below for seals, bearing and other parts...

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed.   This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or...

This part is a Wear Ring that measures 2 5/8" inside Diameter and fits some Aqua-Flo XP2e and Xp3 Impellers except the 3.0HP Xp2e Impeller... That Impeller requires a different Wear Ring which measures 2 3/8" Inside Diameter.. Look at the chart in the...

This is a XP2e 2.0HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps on High at 115V. See the links below for seals, bearing and other parts...

This is a .75HP or 3/4HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End .75HP Motor that has about 7.0 Amps on High Speed at 230V and 7-8.0 Amps at 115V. This Impeller fits between the Face and the...

This is a XP2e 4.0HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V there are no 115V versions. See the links below for seals, bearing and other parts for...

  This is a 1HP Impeller with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.0HP Motor would be about 8.0 Amps on high speed at 230V or 12.0 Amps at 115V.   This Impeller fits between the Face and the...

This is a XP2e 3.0HP Impeller.. The Impeller has a 2 3/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor would be about 12.0 Amps on high speed at 230V there are no 115V versions. Note: If your old impeller has a 2 3/8" Eye this is the...

This is a XP2e 2.5HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.5HP Motor would be about 11.0 Amps on high speed at 230V there are no 115V versions. See the links below for seals, bearing and other parts for...

This is a 2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 2HP Motor that has about 10.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...