XP2 1.5 HP 2 1/8" Eye Impeller & Seal (2) Bearing Kit Aqua-Flo 230V 9 Amp or 115V 14 Amp

(1 review) Write a Review

SKU:: HTP9169CB50asealkit2bearing
Shipping:: Calculated at Checkout

XP2 1.5 HP 2 1/8" Eye Impeller & Seal (2) Bearing Kit Aqua-Flo 230V 9 Amp or 115V 14 Amp
XP2 1.5 HP 2 1/8" Eye Impeller & Seal (2) Bearing Kit Aqua-Flo 230V 9 Amp or 115V 14 Amp
XP2 1.5 HP 2 1/8" Eye Impeller & Seal (2) Bearing Kit Aqua-Flo 230V 9 Amp or 115V 14 Amp
XP2 1.5 HP 2 1/8" Eye Impeller & Seal (2) Bearing Kit Aqua-Flo 230V 9 Amp or 115V 14 Amp
XP2 1.5 HP 2 1/8" Eye Impeller & Seal (2) Bearing Kit Aqua-Flo 230V 9 Amp or 115V 14 Amp
XP2 1.5 HP 2 1/8" Eye Impeller & Seal (2) Bearing Kit Aqua-Flo 230V 9 Amp or 115V 14 Amp

MSRP: $99.99

$78.99

— You save $21.00

Current Stock: 90

Quantity:

Description

Description

This is a 1.5HP Seal, (2) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor would be about 9.0 Amps on high speed at 230V or 14.0 Amps on High at 115V.

Note: The three things you need to know to get the correct Aqua-Flo XP2 or XP2e Impeller is the Eye Width, Voltage and Amperage.. Use the chart with the Voltage and Amperage to determine the HorsePower.. DO NOT rely on the HorsePower on the pump it is usually “Overrated” not accurate.. See Chart Below.. The Eye Size Choices are 2 ⅛”, 2 ⅜” and 2 ⅝”..

This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 Wet End.

This Impeller uses PS-200 Seal kits that can be found Click Here.

Note: This Bearing has a 17mm bearing center hole; some motors on Aqua-Flo pumps have a 15.9mm bearing center hole so measure before ordering.. Put a Note in the space during check out and we will ship a 15.9mm instead..

To determine the HP refer to the chart below..

The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts.

The 48 Frame will be 3 5/8" between or 5 3/16" in a X Pattern and the 56 Frame will be 4 1/8" Between or 5 3/4" in a X Pattern.

You must go by the Amperage Sticker on the motor not stickers on the Wet End or Motor especially the BHP Stickers.

Look on the label of the motor for the two amperages if you have a 2 speed pump or if its a single speed look for a single amperage. An example will look something like this: 10.0/3.5 The 10.0 is the high amperage in this example.

115V Chart Below

3/4HP 8-9 Amps

1HP 11-12 Amps

1.5HP 16-17 Amps

2HP 19-20 Amps. 2HP would be very rare.

230V Chart Below

8.0 = 1 HP

10.0 = 2 HP

12.0 = 3 HP

14.0 = 4 HP

16.0 = 5 HP

NOTE: Your pump or motor may say a different Horse Power than what you see here, DO NOT go by what is listed on the motor, go by the amperage on the label.

NOTE for the NOTE: TRUST ME ON THIS, everybody lies about their Horse Power. But the amperage does not lie. Most people are told incorrectly that they have 5 HP pumps.

If you do the math two 230V 5 HP pumps at 16 amps is: 32 amps. Plus a 5.5 KW heater is: + 21 amps.

That means with both pumps running and the heater on it will draw = 53 AMPS.

I bet your HOT TUB is on a 50 AMP breaker…... Therefore contrary to what you have been told you DO NOT have a 5 or 6 or 7 Hp pump.

Impeller Type

	Closed Face
Impeller Diameter OD	4"
Vane Width ID	5/16"
Eye Diameter OD	2-1/8"
Eye Length	11/16"
Impeller Width OD	9/16"
Seal Seat Depth	1/8"
Shaft Length	1-1/2"
Shaft Diameter OD	5/8"
Seal Seat Diameter OD	1-1/4"
Manufacturer	AquaFlo
Pump Application	XP2

Save

View AllClose

1 Review

1 Review

5
replacing frozen impeller

Posted by Unknown on Nov 25th 2017

watched video on appropriate motor pump for my hot tub nd determined which kit to order. kit arrived and following instructional videos replaced bearings and impeller etc. reassembled and after some electrical problems not associated with pump repair, newly repaired pumpand motor seem to work ok. I will not know how pump works until I fill tub with water. with holidays coming on, had no chance to fill tub, so will see. but parts were exactly what was shown and instructions were right on money. if you have the time and the ability, this is a doable project.