Wavemaster 3000 Complete Pumps

This part is a (4) Bolt head Screws and Washer Kit for 48 or 56 frame pumps used to mount pump motors down on wood based hot tubs. . Includes  (4) Screw head 1 1/8" Screws and (4) Washers.  Note: Rubber mount not included in this listing it can...

This part is a Rubber Pump Motor Base Vibration Dampener with (4) Bolt head Screw and Washer Kit for 48 and 56 frame pumps. Includes 4 soft 'washers' to isolate mounting screws from touching the motor base along with (4) Screw head 1 1/8" Screws and...

This part is a Stronger Pump Bleeder Barb that fits some Watkins Wavemaster XP2, XP2E, LX and others.. It is 1/4" Barb x 1/4"Npt and is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines....

This part is a Pump Bleeder Barb for some Watkins Wavemaster LX Pumps and others.. It is 1/2" Barb x 1/4"Mpt and is used with an unusually large bleeder line.. The line is 1/2" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This...

This Pump is a Replacement for a 0974101-03 or 0974001-03 1.5 HP 230V 8.0/2.6 Amp (2) Speed 48 Frame Complete Pump  It is about 7 1/4"" across the face of the pump, it measures about 7 3/8" from the bottom to the top of the pressure side of the...

This part is a Pump Bleeder Barb fit some Watkins Wavemaster LX Pumps and others.. It is 1/2" Barb x 1/4"Mpt and is used with an unusually large bleeder line.. The line is 1/2" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part...

This part is a Pump Bleeder Barb fits some Watkins Wavemaster XP2, XP2E, LX and others.. It is 1/4" Barb x 1/4"Mpt and is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part...

This part is a Complete Wavemaster 3000 1.0HP Wet End 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Side discharge 48 frame wet end for FMHP pumps. Vendor Code 01484 39584

This part is no longer available you must buy a complete wet end to get this part. This part is a Faceplate found on Wavemaster 3000 side discharge wet ends..   Drain Plug Location    6,8 o`clockSuction Connection (Physical...

This Wavemaster 3000 Face Plate O-Ring Is 5 1/8" Inside Diameter and is 1/8" Thick.   For other parts related to this part see the below links:

This part is a replacement wear ring for Wavemaster 3000 Pump Impellers with a 1 3/4" Eye.. The ring measures about 1 3/4" inside the wear ring and 2 3/16" at the widest part and about 3/4" tall.. For Other related parts see the below...

This is a 1HP Impeller for a Wavemaster 3000 Code 04184 48 Frame Side Discharge pump. This Impeller fits between the Face and the Volute of a Wavemaster 3000 Series Wet End. I would advise replacing the Seal when you replace the Impeller. This Impeller...