Pump Wet Ends and Related Parts

This is a XP2e 4.0HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V there are no 115V versions. See the links below for seals, bearing and other parts for...

  This is a 1HP Impeller with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.0HP Motor would be about 8.0 Amps on high speed at 230V or 12.0 Amps at 115V.   This Impeller fits between the Face and the...

This 2HP Impeller fits a Jacuzzi/Carvin Wet End only and would be found on a motor that is about 16.0 Amps on a 115V motor or 10.0 Amps on a 230V motor..... It can be found under the Name Thera-Max or Thera-Flo and is found on Jacuzzi Premium J Series...

This part is a Wear Ring for a Hi-Flo Impeller found in Waterway Hi-Flo pumps only.. The Inside Diameter of the wear ring is 1 13/16"...

This parts is an Executive 2" Threaded Face plate assembly (Which will measure about 3" Across the Threads) less the O-rings, Screws, Bleeder Plugs and other hardware needed to attach it to the volute..There is another version of the face with a 2 1/2"...

This part is a Impeller, Jacuzzi, J Pump, 1.0hp, 48FR, J Series, JCM Series, K Series, KM Series.. This is found on a Wet End that has a face like I show in the Photo Section only..  Impeller Type Closed Face Impeller Diameter...

Waterway Hi-Flo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 1.5hp, it is used in a Waterway Hi-Flo pump wet end, and must be installed on a 1.5hp (or greater) thru bolt motor. Shaft seal...

This impeller fits a Universal CMP Brand 3HP Wet End only and it requires a Special Seal that you will find a link to below.. This impeller may also have any of the following manufacturer part numbers stamped on the back: 27203-300-300, 27203-000-300,...

This part is a Complete 2HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 48 frame wet end for XP2 pumps. This wet end is used with a 48 frame motor that would have about 10.0 Amps on High Speed on a 230V motor or 16.0...

This is a XP2e 3.0HP Impeller.. The Impeller has a 2 3/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor would be about 12.0 Amps on high speed at 230V there are no 115V versions. Note: If your old impeller has a 2 3/8" Eye this is the...

This is a XP2e 2.5HP Impeller.. The Impeller has a 2 5/8" Eye width for an Aqua-Flo 48 or 56 Frame Wet End 2.5HP Motor would be about 11.0 Amps on high speed at 230V there are no 115V versions. See the links below for seals, bearing and other parts for...

This Kit is an 2HP Impeller for an Executive 48 Frame Wet End up to 2HP Motor and a 56 Frame Wet End 2 HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you...