Watkins Wavemaster Complete Pumps

This part is a (4) Bolt head Screws and Washer Kit for 48 or 56 frame pumps used to mount pump motors down on wood based hot tubs. . Includes  (4) Screw head 1 1/8" Screws and (4) Washers.  Note: Rubber mount not included in this listing it can...

This part is a Rubber Pump Motor Base Vibration Dampener with (4) Bolt head Screw and Washer Kit for 48 and 56 frame pumps. Includes 4 soft 'washers' to isolate mounting screws from touching the motor base along with (4) Screw head 1 1/8" Screws and...

This Kit is a Set of (4) Total Combination of the Two Standard Size 2" Heater or Pump Union Gasket (2) with a 2 1/2" Lip Center to Center and (2) with a 2 5/8" Lip Center To Center. The purpose of this Combo Kit is if you don't know...

This part is a Stronger Pump Bleeder Barb that fits some Watkins Wavemaster XP2, XP2E, LX and others.. It is 1/4" Barb x 1/4"Npt and is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines....

This part is a Pump Bleeder Barb for some Watkins Wavemaster LX Pumps and others.. It is 1/2" Barb x 1/4"Mpt and is used with an unusually large bleeder line.. The line is 1/2" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This...

This is an Aqua-Flo 39577 2.0HP Seal Kit & Impeller with a 2 1/8" Eye Width... This Impeller fits between the Face and the Volute of a XP2 Wet End found on some pumps with Vendor Code 4081. Impeller Type   Closed Face Impeller Diameter...

This Kit is a 2" Pump Union, Slice Valve, Spin Kit To Plumbing Connect Kit with Glue found in many Hot Tubs. The Pump Union which measures about 3" Inside the threads receives a 2"street X 2" Slip Slice Valve then you glue the 2" coupler to spin it to...

This Kit is a 2" Pump Union, Slice Valve, Spin Kit To Plumbing Connect Kit found in many Hot Tubs. The Pump Union which measures about 3" Inside the threads receives a 2"street X 2" Slip Slice Valve then you glue the 2" coupler to spin it to win it on...

This part is a Pump Bleeder Barb fit some Watkins Wavemaster LX Pumps and others.. It is 1/2" Barb x 1/4"Mpt and is used with an unusually large bleeder line.. The line is 1/2" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part...

This part is a Pump Bleeder Barb fits some Watkins Wavemaster XP2, XP2E, LX and others.. It is 1/4" Barb x 1/4"Mpt and is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part...

This is a 2.5HP Seal, (2) Bearings & Impeller Kit with a 2 1/8" Eye Width. This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081. Fits Some Watkins Hot Spring...

This is a 2.5HP Seal, (1) Bearing & Impeller Kit with a 2 1/8" Eye Width. This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081. Fits Some Watkins Hot Spring....