Waterway 56 Frame Pumps
Read this information to Help to determine the Frame and HP.. The way you can determine whether your pump is a 48 or 56 Frame is by measuring the width of the motor. A 48 Frame motor will measure 5 3/4" wide across the back and a 56 Frame will measure about 6 1/2" wide across the back.
For 230 Volt Pumps Look on the label of the motor for the two amperages if you have a 2 speed pump, if its a single speed look for a single amperage. It will look something like this: 10.0/3.5 The 10.0 is the high amperage in this example.
8.0 = 1 HP
10.0 = 2 HP
12.0 = 3 HP
14.0 = 4 HP
16.0 = 5 HP
For 115 Volt Pumps Look on the label of the motor for the two amperages if you have a 2 speed pump, if its a single speed look for a single amperage. It will look something like this: 10.8/2.8 The 10.8 is the high amperage in this example and would equate to a 1 HP.
8.0 = .5 HP
9.0-10.0 = .75 HP
10.0-13.00 = 1 HP
13.5-15.0 = 1.5 HP
16.0-20.0 = 2 HP
Note: These Amperages are Averages so find the Amperage closest to your pumps Amperage. Note for the Note: 2HP 115V pumps are very rare, do not order one thinking you can add more power. This pump or even a 1.5HP pump will cause your PLug N Play tub to damage the electrical system, Plug, Wires and even the pump motor.
NOTE: Your pump or motor may say a different Horse Power than what you see here, DO NOT go by what is listed on the motor, go by the amperage on the label.
NOTE for the NOTE: TRUST ME ON THIS, everybody lies about their Horse Power. But the amperage does not lie. Most people are told they have 5 HP pumps, if you do the math two 5 HP pumps at 16 amps is 32 amps. Plus a 5.5 KW heater is 21 amps. That means with both pumps running and the heater on it will draw 53 AMPS. I bet your HOT TUB is on a 50 AMP breaker. Therefore contrary to what you have been told you DO NOT have a 5 or 6 or 7 Hp pump.
- Product
- Qty in Cart
- Quantity
- Price
- Subtotal
-
Barb Adapter, 3/8"b x 1/4"mpt, With Silicon Kit Pump Wet End Face fits Aqua-Flo & CMP
MSRP: $12.99$8.99This kit is a Air Bleeder barbed plug and Silicon sealer usually used on a Aqua-Flo and CMP Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands of Hot Tubs just compare the pictures and...MSRP: $12.99$8.99 -
Barb Bleeder 1/4" Mpt X 3/8" with Silicon Kit for Waterway Pump Fitting
MSRP: $17.99$11.99This kit is anAir Bleeder barbed plug and Silicon sealer usually used on a Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands just compare the pictures and measurements with your...MSRP: $17.99$11.99 -
3/8" Clear Vinyl Tubing, 12" length for Air Manifold, Jet Body, Blower Jet, Pump Bleeder
MSRP: $4.99$3.99This part is a 12" Piece of 3/8" Clear Tubing used with Air Valves... If you need 3 feet order (3x) and it will ship uncut.. This tubing measures 3/8" Inside Diameter and 1/2" O.D. and is used in most Air Applications on most tubs from the air...MSRP: $4.99$3.99 -
How To Video Hot Tub Broken Pump Union Emergency Repair The Spa Guy How To Series
$0.00In this video The Spa Guy shows you how to repair a broken Hot Tub Pump Union without cutting plumbing out and using an Emergency Pump Union Split Nut Kit... #sparepair #hottubrepair #thespaguy...$0.00Qty in Cart: 0Price:$0.00Subtotal: -
How To Video GFCI Breaker Tripping New Wire Up Hot Tub Diagnose The Spa Guy
$0.00This video is The Spa Guy teaching you how to Diagnose a New Wire Up Situation where you just wired your hot tub up and it is tripping the breaker and it is either a new tub or it is used and ran fine at the last location...... Save$0.00Qty in Cart: 0Price:$0.00Subtotal: -
How To Video Waterway Executive Pump Seal Impeller & Bearing Replacement How To The Spa Guy
$0.00In this Video The Spa Guy tells you How To Replace a Waterway Executive Pump Seal,,Impeller & Bearing... Save Save Save Save Save Save Save Save Save Save Save Save Save Save Save Save Save Save$0.00Qty in Cart: 0Price:$0.00Subtotal: -
Set of (2) Hot Tub Spa 2" Slip X 2" Threaded Pump Unions Video How To
MSRP: $23.99$18.99This set is a Set of (2) 2" Slip X 2" Threaded Pump Union with Gasket or O-ring that matches Union. The Union recieves a 2" pipe or fitting on one side and then Screws to a 2" Wetend(Pump) Threaded Part on the...MSRP: $23.99$18.99 -
Pump Motor Base, Rubber, 48 & 56 Frame, Vibration Dampener
MSRP: $14.99$11.99This part is a Rubber Pump Motor Base Vibration Dampener for 48 and 56 frame pumps. Includes 4 soft 'washers' to isolate mounting screws from touching the motor base. This motor base mounting pad fits under any 48 frame pumps, and under most 56 frame...MSRP: $14.99$11.99 -
Barb Adapter, 3/8"b x 1/4"mpt Pump Wet End Face fits Waterway
MSRP: $11.99$8.99This part is a Bleeder Barb that is 3/8" barb x 1/4" Threaded MPT fitting fits Wet End Face Bleeder Plug Holes to attach a Bleeder Line it fits Waterway Executive 48 & 56 Frame Parts & Wetends, Power-Right 9089X, 9094X,...MSRP: $11.99$8.99 -
2 1/2" Split Nut Kit for Pump Union Emergency Repair
MSRP: $24.99$19.99This part is a 2 1/2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 2 1/2" Pump Union. The Pump Union Split Nut that measures about 3 3/4" on the outside and mounts to the existing Pump Union Body using 2...MSRP: $24.99$19.99 -
Hot Tub Spa 2" Slip X 2" Threaded Pump Union & Gasket How To Video
MSRP: $12.99$9.99This part is a 2" Slip X 2" Threaded Pump Union with Gasket or O-ring that matches Union. The Union receives a 2" pipe or fitting on one side and then Screws to a 2" Wetend(Pump) Threaded Part on the other...MSRP: $12.99$9.99 -
(1X) 2" Split Nut Kit for Pump Union Emergency Repair Video How To
MSRP: $24.99$14.99This part is a 2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 2" Pump Union. The Pump Union Split Nut that measures about 3" on the Inside of the Threaded Side and mounts to the existing Pump Union Body...MSRP: $24.99$14.99