Pumps and Related Parts

You are buying a 1.5 HP 48 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Screws, Volute, Impeller, Seal, Face and the Wear Ring. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be...

This part is a Complete Verticle Mount Style Waterway Iron- Might or Uni-Might 1/15thHP Wet End that is 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Adjustable Suction Side discharge 48 frame wet end for FMVP pumps only.  This...

Balboa / Vico Ultima side discharge circulation pump with 1.5" unions (2-3/8" thread diameter) can be found plumbed to your heater and is usually set to run 24/7 providing a light and efficient circulation. Rated at 230 Volts and comes with a .6-.7 amp...

This part is a Pump Motor only that is 48 frame 115V 2 speed with 8.8.0 Amps on High Speed and 2.9A on Low Speed. Some of these motors have the BHP or SPL marking of 1.0 HP but it is truley a .75 HP motor. You can find wet ends for this motor by...

1.0 Hp single speed thru-bolt pump motor in the 48Y frame style. This motor runs at 230 Volts and draws 6.0 amps. Motor Type Spa Motor Amperage 6.0A Voltage 230v Frame Type 48Y Speed 1 Speed (1-Spd) Horsepower 1.0hp Total Horsepower 1...

This part is a Complete Flo-Master CMCP 1/15HP Aqua-Flo 1-1/2" x 1-1/2" ( Which measures about 2 3/8" Across the Threads) Center discharge 48 frame wet end for 48FR pumps. This wet end is used with a 48 frame motor that would have about 0.6 Amps on a...

This Kit is a Set of 2 NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring...

This part is a LX Pump Union 11/64" Thick 2 5/8" Center to Center O-Ring World's Finest Pump Union. The O-Ring is 2 5/8" Center to Center across and 11/64" Thick where the standard O-Ring is about 1/8" Thick. This fits LX Pump unions that say...

THERA-MAX 2.5HP 2 SPEED BASELESS PUMP FOR JACUZZI AND SUNDANCE SPAS Only   This pump is a Jacuzzi / Sundance, Baseless, TheraMax, 48FR, 2.5HP, 2SP, 230V that measures about 3" across the threads.. The amperage is 10.0-12.0 Amps on high speed and 3...

This Kit is a 2" Sweep Pump Union To Plumbing Connect Kit found in many Hot Tubs.   The 2" Sweep Pump Union which measures about 3" Inside the threads receives a 2"street X 2" Slip Slice Valve then you glue the 2" Street X Slip 90° fitting on...

This Kit is a 2" Sweep Pump Union To Plumbing Connect Kit found in many Hot Tubs.   The 2" Sweep Pump Union which measures about 3" Inside the threads receives a 2"street X 2" Slip Slice Valve then you glue the 2" Street X Slip 90° fitting on...

This is a 2.5HP Impeller with a 2 1/8" Eye width for a Waterway 48 or 56 Frame Wet End 2.5HP Motor that is about 11.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Waterway EX2 Wet End which is very rare and odd. I would...