Jacuzzi Whirlpool Hot Tub and Bath Parts

This Kit is a Set of (2) Jacuzzi J Pump Style Pump Unions with 1 1/2" Slice Valves. The 1 1/2" Slice valve will glue inside the J pump union then you glue your 1 1/2" pipe which measures about 1 7/8" OD into the slice valve. The J Pump Union receives...

This Kit is a 1 1/2" Spigot X 1 1/2" Slip Slice Gate Valve and Jacuzzi® J Style Pump Union with O-Ring that matches Union. The Valve receives a 1 1/2" pipe or fitting on one side that would measure 1 7/8" ID and then...

This set is a Set of (2) 2" Slip X 2" Threaded Pump Union with Gasket or O-ring that matches Union. The Union recieves a 2" pipe or fitting on one side and then Screws to a 2" Wetend(Pump) Threaded Part on the...

This part is a Set of (2) 2 1/2" Therm Style Pump or Heater Union Gasket Only for use with a 2 1/2" Heater or Pump Union. If your heater or Pump is 2 1/2" this part could be correct we offer (2) different sizes of 2 1/2" gaskets so you need to...

This part is a 2 1/2" Thread X 1" 90 Degree Barb Heater Union with Gasket that matches Union.   The Union receives a 1" ID pipe on the barb side and then Screws to a 2 1/2'" Heater Flange using a 2 1/2" Nut on the heater side...

This Kit is a Set of (2) 2" Spigot X 2" Slip Slice Gate Valve Kit with a Jacuzzi® J Style Pump Unions with O-rings, (2) 2" Street x Slip Slice Gate Valve and (2) 2" Couplers for glueing 2" plumbing to the slice valve...

This Kit is a 2" Spigot X 2" Slip Slice Gate Valve Kit with a Jacuzzi® J Style Pump Union with O-ring and a 2" Coupler for gluing 2" plumbing to the slice valve.  The Valve receives a 2" pipe or fitting on one side and...

This Kit is a Set of (2) Jacuzzi® J Pump Style Pump Union that can be used on 1 1/2" or 2" Plumbing systems. This union can receive a 1 1/2" plumbing part inside the back of the union or a 2" Plumbing part glued to the...

This item is a 2 1/2"" Heater Union Tailpiece with a Gasket that is used on may heater tubs that measure about 3" inside diameter of the tube.. It also has a 90 degree 1" Barb fitting.. If you need a gasket for this union click this link.. 2 1/2"...

This part is a 2 1/2" Thread X 1" 90 Degree Barb Heater Union. The Union receives a 1" ID pipe on the barb side and then Screws to a 2 1/2'" Heater Flange using a 2 1/2" Nut on the heater side. This part is used on Heaters that are...

This part is a Impeller, Jacuzzi, J Pump, 1.0hp, 48FR, J Series, JCM Series, K Series, KM Series.. This is found on a Wet End that has a face like I show in the Photo Section only..  Impeller Type Closed Face Impeller Diameter...

This part is an Jacuzzi J Pump Impeller Wear Ring.. It measures about 1 15/16" ID and 2 7/16" to the outermost OD..  Fits the following pumps: Cygnet Series - All Horsepowers J, JCM, K and KM Series - All Horsepowers L, LC, LCUN2,...