Hot Tub Parts by Tub Brand

This part is a Diverter Kit with a Stem, Silver "S" Style 4 5/16" Long Diverter Handle, Graphite 3 11/16" Graphite Cap & O-ring Kit. This Diverter Knob has a S Shaped Top and mounts on top of the Diverter Valve Stem Square that is...

This part is a Reinforced "S" Style 4 5/16" Gray Spa Diverter Handle Knob only. This Diverter Knob has a S Shaped Top and mounts on top of the Diverter Valve Stem Square that is about 7/16" Wide sticking through the diverter cap. The...

This part is a Silver "S" Style 4 5/16" Long Diverter Handle and Graphite 3 11/16" Graphite Cap & O-ring Kit only. This Diverter Knob has a S Shaped Top and mounts on top of the Diverter Valve Stem Square that is about 7/16" Wide...

This part is a Silver "S" Style 4 5/16" Long Diverter Handle and Graphite 3 11/16" Graphite Cap only. This Diverter Knob has a S Shaped Top and mounts on top of the Diverter Valve Stem Square that is about 7/16" Wide sticking through the...

This part is a "S" Style 4 5/16" Silver Spa Diverter Handle Knob only. This Diverter Knob has a S Shaped Top and mounts on top of the Diverter Valve Stem Square that is about 7/16" Wide sticking through the diverter cap. The Diverter Valve...

This New Old Stock part is a Complete Hot Tub Spa Part Gray 11" Waterfall Assembly 3 Hole Style Graphite Gray Hole size is about 1 3/4" each.. You will get a 90 degree 3/4' Barb with the waterfall.. These Waterfalls are hard to come by but we do have...

This part is a Heater M7 Sensor with a 31" wire found in Jacuzzi Premium J series 2016 to current.  Note: This sensor does not have the nut and washer on it so it will only work with Jacuzzi Premium hot tubs..   Application Balboa...

  Filter, Cartridge, 30sqft, 1-1/4" Female SAE Thread, 4-3/4" Wide, 11-3/8" Tall Note: The 1 1/4" Thread is a very usual size are sure you are correct before ordering..   These are found on some Saratoga Hot Tubs.  Bottom Physical...

This Vendor Code 3536 2.5 Horse Power Impeller, Seal, Silicon & Seal Installation Tool that fits a 56 Frame Pump Wet Ends manufactured by Intertek with numbers 39578-03, 37066-03 or 0982601-03 only.  See NOTES Below... Watch the video...

This part is a Pump Bleeder Barb fit some Watkins Wavemaster LX Pumps and others.. It is 1/2" Barb x 1/4"Mpt and is used with an unusually large bleeder line.. The line is 1/2" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part...

As of 11/2024 Aqua-flo has started to send this pump with a capacitor bump in an odd spot that may affect your installation. In light of that we are now sending this pump assembly out as a separate 10.5 Amp motor and a genuine 2.5 HP XP2 wetend. You...

This part is a PVC Tee, 1"slip x 2"slip x 1"slip.. You can make your connection back to the small side using the below kit..  Connect kit for 1" Soft pipe Click Here.. 1" Connect Kit Jacuzzi J Pump Fittings found here: Jacuzzi® J Pump...