Watkins Wavemaster Wet Ends Hot Spring Solana

This part is a Complete Wet End for Vendor Code 3536 with pump numbers 39578-03, 0982601-03 or 37066-03. This is for Hot Spring Watkins Pumps 2" X 2" 2.5HP 230V Vendor Code 3536 only.   It is about 7 1/4"" across the face of the pump, it...

This Wet End for Watkins 0974101-03 or 0974001-03 1.5HP 48Fr LX Pump 2" X 2" only that would be about 8.0 Amps at 230V Vendor Code 3536..  It is about 7 1/4"" across the face of the pump, it measures about 7 3/8" from the bottom to the top of the...

This Part is a Complete Wet End, 77773, Watkins, 36746, 72194, 72197, 2.0HP, 230v, 48 frame, 2" x 2", 8.5A, Vendor Code 4081, Wavemaster..   This Wet End is a 48Frame 2" x 2" inlet and outlet Wet End that measures about 3" across the threads....

This Complete Wet End fits a 39577-03 Vendor Code 3536 10 Amp 56 Frame Pump 77712.. It is about 7 1/4"" across the face of the pump, it measures about 7 3/8" from the bottom to the top of the pressure side of the volute, it also measures 4 13/16"...

This Item is a Wear Ring for the Lifesmart Hot Tub pump with the part number 1431501-03. It may have a Watkins Vendor Code 3536 on the LX Brand Pump. These pumps usually have the part number 1431501-03 on the label for a Watkins Version. NOTE: Do Not...

This complete pump and motor is a Watkins Wavemaster 6000 or 7000 replacement, 36675-03.. This pump is a 115V or 230V, (1) Speed, 17.0Amp or 8.5Amp, 48 frame 2" x 2" XP2 pump and motor... The 2" inlet and outlet measure about 3" across the threads.....

This part is a Pump Shaft Water Slinger designed to sling water away from the motor front bearing in case of a seal leak and it fits All Brands of Hot Tub Pumps..   This part goes on the shaft before you install the wet end.. 

This Kit is a Set of (2) NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this...

This part is a Stronger Pump Bleeder Barb for some Watkins Wavemaster XP2, XP2E, LX and others.. It is 1/4" Barb x 1/4"Npt and is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines....

Red Epoxy is a new high performance, two-part, heat cured, epoxy repair kit for making permanent repairs on all metals and rigid plastics. Red Epoxy is specifically designed to exhibit a distinct color change when heat cured. Red Epoxy will provide a...

This part is a Pump Bleeder Barb for some Watkins Wavemaster LX Pumps and others.. It is 1/2" Barb x 1/4"Mpt and is used with an unusually large bleeder line.. The line is 1/2" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This...

This is a Watkins Wavemaster 39577 2.0HP Seal Kit & Impeller with a 2 1/8" Eye Width... This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081. Impeller...