Hotspring, Watkins, Vendor #4081, (1) Bearing, Shaft Seal Kit with Silicon & Tool, Wavemaster

(2 reviews) Write a Review
SKU:
ASPPS-LEEBearing4081
Shipping:
Calculated at Checkout
  • Hotspring, Watkins, Vendor #4081, (1) Bearing, Shaft Seal Kit with Silicon & Tool, Wavemaster
  • Hotspring, Watkins, Vendor #4081, (1) Bearing, Shaft Seal Kit with Silicon & Tool, Wavemaster
  • Hotspring, Watkins, Vendor #4081, (1) Bearing, Shaft Seal Kit with Silicon & Tool, Wavemaster
  • Hotspring, Watkins, Vendor #4081, (1) Bearing, Shaft Seal Kit with Silicon & Tool, Wavemaster
  • Hotspring, Watkins, Vendor #4081, (1) Bearing, Shaft Seal Kit with Silicon & Tool, Wavemaster
  • Hotspring, Watkins, Vendor #4081, (1) Bearing, Shaft Seal Kit with Silicon & Tool, Wavemaster
  • Hotspring, Watkins, Vendor #4081, (1) Bearing, Shaft Seal Kit with Silicon & Tool, Wavemaster
  • Hotspring, Watkins, Vendor #4081, (1) Bearing, Shaft Seal Kit with Silicon & Tool, Wavemaster
  • Hotspring, Watkins, Vendor #4081, (1) Bearing, Shaft Seal Kit with Silicon & Tool, Wavemaster
  • Hotspring, Watkins, Vendor #4081, (1) Bearing, Shaft Seal Kit with Silicon & Tool, Wavemaster
MSRP: $39.99
$29.99
— You save $10.00

Description

This Kit Fits Watkins, Vendor #4081, Wavemaster Pumps.

This Kit Features (1) Bearing, Seal Tool, Silicone & (1) Seal for Vendor Code #4081 Pumps on Hotspring Watkins Hot Tubs..

Note: Watkins used 5 different Brands of Wet Ends under the Wavemaster name.. Be sure that yours says 4081 on the label..

 

Additional Note: These pumps can have (2) different size bearings.. The standard 17mm hole will be shipped with this order if you are able to measure and yours is the smaller 15.9mm version add a note when checking out.. If you are not able to measure and you have the smaller versions you simply ship them back with a note that you need the smaller version and we will ship the other size back..

 

The Spring Seal part goes onto the shaft of the Impeller and the Ceramic & Rubber part that goes into the Volute. The Hole in both parts is about 5/8". To Install you should put silicon sealant on the shaft of the Impeller and gently push it onto shaft after you have put a small amount of The Professors Silly Juice on the Impeller Shaft. Also the rubber part can use a light coat of silicon to slide it into place in the Volute or Wet End Body. We offer these alone, with The Professor's Silly Juice (Special Hot Tub Silicon Sealer) or with an Impeller in a kit. So if you need an impeller look for the Hotspring Wavemaster Impeller Kit.

 

Please note: When you have a seal leaking in most cases you will need an impeller because the leak caused water to get into the metal shaft area that the impeller is screwed onto and expands and damages the impeller.

This Seal Fits some Wavemaster Wet Ends on Watkins Hotspring Tubs. This listing is for the seal and Silicon only any other parts are for illustration only!!

 

Save

Save

View AllClose

2 Reviews

  • 5
    Bearing seal kit

    Posted by Mike Sorbel on May 28th 2023

    Works perfectly

  • 5
    6203 bearing and Seal

    Posted by Unknown on Dec 19th 2016

    Please put the bearing # 6203 in the part description. I was not sure if it was a 6203 bearing. I think it is wise to replace both front and rear bearing at the same time, so this kit should offer an option to get both bearings and the pump seal. The seal fit perfect.

View AllClose