Complete Wet End, Aqua-Flo ,XP2, Xp2e, 2.5HP, 2"x 2" , 48fr, fits Motors with 11.0A/230V

(1 review) Write a Review
SKU:
HTP34-402-1208
Shipping:
Calculated at Checkout
  • Complete Wet End, Aqua-Flo ,XP2, 2.5HP, 2"x 2" , 48fr, fits Motors with 11.0A/230V 
The Suction and Pressure sides both Measure about 3" Across the threads!
  • This is a chart you can use to determine which Aqua-Flo version you have..
This is a 48 Frame Wet End. Measures about 3 5/8" between the bolt hole to determine which one you have.
  • Complete Wet End, Aqua-Flo ,XP2, 2.5HP, 2"x 2" , 48fr, fits Motors with 11.0A/230V
  • Complete Wet End, Aqua-Flo ,XP2, 2.5HP, 2"x 2" , 48fr, fits Motors with 11.0A/230V
  • Complete Wet End, Aqua-Flo ,XP2, 2.5HP, 2"x 2" , 48fr, fits Motors with 11.0A/230V 
The Suction and Pressure sides both Measure about 3" Across the threads!
  • Complete Wet End, Aqua-Flo ,XP2, 2.5HP, 2"x 2" , 48fr, fits Motors with 11.0A/230V
  • Complete Wet End, Aqua-Flo ,XP2, 2.5HP, 2"x 2" , 48fr, fits Motors with 11.0A/230V
MSRP: $137.99
$114.99
— You save $23.00

Description

This part is a Complete 2.5HP Aqua-Flo 2" x 2" ( Which measures about 3" Across the Threads) Side discharge 48 frame wet end for XP2 pumps. This wet end is used with a 48 frame motor that would have about 11.0 Amps on High Speed on a 230V motor and not available for a 115v motor. The motor used may be either a single or dual speed. The wet end may be rotated 90 degrees to change the discharge position. The complete wet end includes: the volute, seal, impeller, wear ring, suction cover, suction cover o-ring, drain plug, drain plug o-ring and suction cover screws.

 

If you need a barb for the front of your wet end where a small hose connects here are choices for those Barbs with or without sealer.. I always seal these with silicon Pipe tape does not work well on these fittings:

 

Barb Adapter, 3/8"b x 1/4"mpt, Pump Wet End Face fits Aqua-Flo & CMP

Barb Adapter, 3/8"b x 1/4"mpt, With Silicon Kit Pump Wet End Face fits Aqua-Flo & CMP

Note: You always base your choice of HP on the Amperage of the motor it is going on see the chart below.. a 48 frame motor measures about 5 1/2" across the motor and will have 1/4" heads on the thru-bolts and will measure about 5 3/16" between the thru-bolts in a cross pattern and 56 frame motor measures about 6 1/4" across the motor and will have 5/16" heads on the thru-bolts and will measure about 5 7/8" between the thru-bolts in a cross pattern..

 
Related Parts:
 

 Horsepower VS Amperage Chart

All of these numbers are approximate but will be very close..
115v
.75HP=10Amps
1.0HP= 12Amps
1.5HP=14Amps
2.0HP= 16Amps
 
230V
1.0HP= 8.0 Amps
2.0HP=10.0 Amps
3.0HP=12.0 Amps
4.0HP=14.0 Amps
5.0HP-16.0 Amps
 
View AllClose

1 Review

  • 5
    wet-in replacement

    Posted by edward b eschmann on Sep 14th 2020

    watched all the videos and purchased parts through the hot tub guy and I am back and running. Couldn't be happier.

View AllClose